Влияние низкомодульных включений BN на свойства Y-TZP керамики
| Parent link: | Перспективные материалы № 4.— 2019.— [С. 49-56] |
|---|---|
| Main Author: | |
| Corporate Author: | |
| Other Authors: | , |
| Summary: | Заглавие с экрана Рассмотрено влияние импульсного и непрерывного режимов обработки пучками газовых ионов на физико-механические свойства циркониевой керамики. Импульсный режим обработки ионами N2+ реализован при ускоряющем напряжении 250 - 300 кВ, плотности тока j = 150-200 А/см2 и плотности энергии W = (3,5 и 5) ± 5 % Дж/см2; непрерывный режим обработки ионами Аr+ - при ускоряющем напряжении 30 кВ, плотности ионного тока j 300 и 500 мкА/см2 при флюенсе от 1016 до 1018 см-2. Установлено, что импульсный режим ионной обработки приводит к оплавлению и рекристаллизации поверхности керамики. Показано, что такая обработка создает нарушения стехиометрии по кислороду в керамике и в результате наблюдается появление электропроводности в приповерхностных слоях. Показано, что непрерывный режим ионной обработки не приводит к оплавлению и рекристаллизации поверхности керамики, но сопровождается ее незначительным травлением, при этом происходит увеличение микротвердости (на 14 %). Упрочнение поверхностных слоев керамики наблюдается на глубине, которая превышает средний проецированный пробег ионов в 103 раз. The article considers the influence of the treatment modes by N2+ and Ar+ ions beams on the physical and mechanical properties of zirconia ceramics. Surface modification of zirconia ceramics was performed using two modes of ion treatment - pulsed and continuous. The pulse mode of treatment by N2+ ions was realized at an accelerating voltage of 250 - 300 kV, current density j = 150 - 200 A/cm2, and energy density W = (3.5 and 5) ± 5 % J/cm2. The continuous mode of treatment by Ar+ ions was realized at an accelerating voltage of 30 kV and an ion current density of 300 and 500 ?A/cm2. The fluence of the Ar+ ion beam varied from 1016 to 1018 cm-2. It is established that the pulsed mode of ion treatment leads to the melting and recrystallization of the surface of ceramics. It is shown that this treatment leads to a violation of the oxygen stoichiometry in ceramics and, as a result, there is an appearance of electrical conductivity in the near-surface layers, the layers of zirconia ceramics become conductive. It was established that the continuous mode of ion treatment does not lead to the melting and recrystallization of the ceramics surface, but is accompanied by its slight etching. It is shown that under the action of continuous ion treatment, microhardness increases (by 14 %). Hardening of the surface layers of ceramics is observed at a depth that exceeds the average projected range of Ar+ ion by 103 times. Режим доступа: по договору с организацией-держателем ресурса |
| Published: |
2019
|
| Subjects: | |
| Online Access: | https://www.elibrary.ru/item.asp?id=37311465 |
| Format: | Electronic Book Chapter |
| KOHA link: | https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=664309 |