Strength of Cutting Tool in Titanium Alloy Machining; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)

Strength of Cutting Tool in Titanium Alloy Machining; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)

Dades bibliogràfiques
Parent link:	Key Engineering Materials: Scientific Journal Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015).— 2016.— [P. 427-431]
Autor principal:	Kozlov V. N. Victor Nikolayevich
Autor corporatiu:	Национальный исследовательский Томский политехнический университет (ТПУ) Институт кибернетики (ИК) Кафедра технологии автоматизированного машиностроительного производства (ТАМП)
Altres autors:	Zhang J. Y.
Sumari:	Title screen In this paper, contact conditions between cutting tool and work material, strength of cutting tool are analyzed. Experimental and theoretical studies of contact load distribution on the artificial flank wear-land that appears on the cutter in a free orthogonal turning disk of titanium alloy (Ti-6Al-2Mo-2Cr) are described. Calculations of internal stresses by the method of finite elements show that for the sharp cutter the main stresses into cutting wedge near to the cutting edge are compression stresses, very large (10 000 MPa) and exceed ultimate compression stress for cemented carbide. Decreasing of main stress with appearance of wear on the flank explains ability working of cutter even at large wear on the flank. Increasing of cutter’s break off probability with appearance of large wear on the flank is explained by increasing of zone where the internal stresses are large enough (more or equal 3 000 MPa) and increasing of defects probability into this zone, which serves as source of cracks. Режим доступа: по договору с организацией-держателем ресурса
Idioma:	anglès
Publicat:	2016
Col·lecció:	Mechanical Engineering Technology
Matèries:	электронный ресурс труды учёных ТПУ контактные нагрузки прочность режущие инструменты износ титановые сплавы
Accés en línia:	http://dx.doi.org/10.4028/www.scientific.net/KEM.685.427
Format:	Electrònic Capítol de llibre
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=646454

Ítems similars

Strength of inserts in titanium alloy machining; IOP Conference Series: Materials Science and Engineering; Vol. 124 : Mechanical Engineering, Automation and Control Systems (MEACS2015)
per: Kozlov V. N. Victor Nikolayevich
Publicat: (2016)

Distribution of contact loads over the flank-land of the cutter with a rounded cutting edge; IOP Conference Series: Materials Science and Engineering; Vol. 124 : Mechanical Engineering, Automation and Control Systems (MEACS2015)
per: Kozlov V. N. Victor Nikolayevich
Publicat: (2016)

Influence of cutting tool wear on contact stresses and temperature distribution in titanium alloy machining; Высокие технологии в современной науке и технике (ВТСНТ-2016)
Publicat: (2016)

Influence of Cutting Tool Wear on Contact Stresses and Temperature Distribution in Titanium Alloy Machining; Key Engineering Materials; Vol. 743 : High Technology: Research and Applications (HTRA 2016)
Publicat: (2017)

Influence of Chip Formation Characteristics on Flank Contact Load Distribution in Titanium Alloy Cutting; Applied Mechanics and Materials; Vol. 756 : Mechanical Engineering, Automation and Control Systems (MEACS2014)
per: Kozlov V. N. Victor Nikolayevich
Publicat: (2015)

Calculation of Contact Stresses during Titanium Alloy Cutting; Key Engineering Materials; Vol. 769 : High Technology: Research and Applications (HTRA 2017)
Publicat: (2018)

Machining of Titanium Alloys with Wave Milling Cutters; Materials Science Forum; Vol. 927 : Materials and Processing Technology II
per: Korovin G. I.
Publicat: (2018)

Fundamentals of Metal Cutting and Machine Tools
per: Juneja B. L.
Publicat: (New Delhi, New Age International Limited, Publishers, 1995)

Problems of cutting tool strength in machining of titanium alloys; Научная инициатива иностранных студентов и аспирантов российских вузов; Т. 1
per: Ogidon Oluwole
Publicat: (2013)

Strength and Stiffness Calculation of Small Diameter Gun Drills; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Babaev A. S. Artem Sergeevich
Publicat: (2016)

Oriented Microtexturing on the Surface of High-Speed Steel Cutting Tool; AIP Conference Proceedings; Vol. 1783 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2016
Publicat: (2016)

Mathematical Simulation of Hydraulic Power Pulse Machine at Matlab; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Tsigankova M. V. Maria Viktorovna
Publicat: (2016)

Development of Graphical Interface for Determination of Optimal Cutting Parameters in Turning Operations; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Bogoljubova (Bogolyubova) M. N. Mariya Nikitichna
Publicat: (2016)

The Influence of the Pouring Temperature on the Structure and Properties of Copper Metal Alloys; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Korchmit A. V. Anton Viktorovich
Publicat: (2016)

Mathematical simulation and optimization of cutting modes in turning of titanium alloy workpieces; IOP Conference Series: Materials Science and Engineering; Vol. 124 : Mechanical Engineering, Automation and Control Systems (MEACS2015)
Publicat: (2016)

Treeing Morphology in Oil Shale; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
Publicat: (2016)

Flexible Process Model Design; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Rudometkina M. N. Monika Nikolaevna
Publicat: (2016)

Software Traceability – A Key to Improve Software Evolution; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Ponomarev A. A. Aleksey Anatolievich
Publicat: (2016)

Effect of Ultrasonic Impact Treatment on Microstructure and Mechanical Properties of Commercial Purity Titanium; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Hairullin (Khayrullin) R. R. Rustam Ravilievich
Publicat: (2016)

SLS Setup and its Working Procedure; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
Publicat: (2016)

Production of Powders by the Method of Electrospark Dispersion; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
Publicat: (2016)

Formalized Approach in Relational Database Design; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Osipova V. V. Viktoriya Viktorovna
Publicat: (2016)

Optimality Conditions for Pareto-Optimal Solutions; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Gorbunov V. M. Vladimir Mikhailovich
Publicat: (2016)

Simulation of the Acoustic Field of Antenna Arrays; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
Publicat: (2016)

Structural Scale Levels of Plastic Deformation and Fracture of High-Strength Titanium Alloy Welds; Physical Mesomechanics; Vol. 21, iss. 5
Publicat: (2018)

Influence of Severe Plastic Deformation on Physicomechanical Properties of Ti-40 mas % Nb Alloy; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
Publicat: (2016)

Property Investigation of Pt-Rh Alloy Nanopowders Obtained by Conductor Electric Explosion Method; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
Publicat: (2016)

Spectral Analysis of Narrow Band Periodic Signals; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Avramchuk V. S. Valery Stepanovich
Publicat: (2016)

Friction Influence on the Accuracy of the Rotors Automatic Balance; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
Publicat: (2016)

Methodological Aspects of Evaluation of Foundry Technologies Effectiveness; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Ardashkin I. B. Igor Borisovich
Publicat: (2016)

Two-Step Synthesis of Tungsten and Molybdenum Disulfides; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Irtegov Yu. A. Yuri Aleksandrovich
Publicat: (2016)

Development of a Queuing System with Dynamic Priorities; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Apachidi X. N.
Publicat: (2016)

Discrete-Event Approach to Simulation of Queueing Networks; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
Publicat: (2016)

Using Parallel Computing in Queueing Network Simulation; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
Publicat: (2016)

Microstructure and Properties of the Composite on the Basis of Copper and Diamond; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Ivashutenko A. S. Alexander Sergeevich
Publicat: (2016)

Properties of WC-6Co Hard Alloy Powders Obtained by the Method of Spark Plasma Dispersion; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
Publicat: (2016)

Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015): The IV International Conference, April 21-24, 2015, Tomsk, Russia; [proceedings]; Key Engineering Materials
Publicat: (2016)

Universal Reference Test Blocks for Liquid Penetrant Testing; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
Publicat: (2016)

Distributed Information System for Processing and Storage of Meteorological Data; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
Publicat: (2016)

Source Code Analysis: Current and Future Trends & Challenges; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
per: Ponomarev A. A. Aleksey Anatolievich
Publicat: (2016)