Estimating Low- and High-Cyclic Fatigue of Polyimide-CF-PTFE Composite through Variation of Mechanical Hysteresis Loops; Materials; Vol. 15, iss. 13
| Parent link: | Materials.— .— Basel: MDPI AG Vol. 15, iss. 13.— 2022.— Article number 4656, 17 p. |
|---|---|
| Tác giả khác: | , , , , |
| Tóm tắt: | Title screen The fatigue properties of neat polyimide and the “polyimide + 10 wt.% milled carbon fibers + 10 wt.% polytetrafluoroethylene” composite were investigated under various cyclic loading conditions. In contrast to most of the reported studies, constructing of hysteresis loops was performed through the strain assessment using the non-contact 2D Digital Image Correlation method. The accumulation of cyclic damage was analyzed by calculating parameters of mechanical hysteresis loops. They were: (i) the energy losses (hysteresis loop area), (ii) the dynamic modulus (proportional to the compliance/stiffness of the material) and (iii) the damping capacity (calculated through the dissipated and total mechanical energies). On average, the reduction in energy losses reached 10–18% at the onset of fracture, whereas the modulus variation did not exceed 2.5% of the nominal value. The energy losses decreased from 20 down to 18 J/m3 (10%) for the composite, whereas they reduced from 30 down to 25 J/m3 (17%) for neat PI in the low-cycle fatigue mode. For high-cycle fatigue, energy losses decreased from 10 to 9 J/m3 (10%) and from 17 to 14 J/m3 (18%) for neat PI and composite, respectively. For this reason, the changes of the energy losses due to hysteresis are of prospects for the characterization of both neat PI and the reinforced PI-based composites Текстовый файл |
| Ngôn ngữ: | Tiếng Anh |
| Được phát hành: |
2022
|
| Những chủ đề: | |
| Truy cập trực tuyến: | https://doi.org/10.3390/ma15134656 |
| Định dạng: | Điện tử Chương của sách |
| KOHA link: | https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=685544 |
MARC
| LEADER | 00000naa0a2200000 4500 | ||
|---|---|---|---|
| 001 | 685544 | ||
| 005 | 20260319115302.0 | ||
| 090 | |a 685544 | ||
| 100 | |a 20260319d2022 k||y0rusy50 ba | ||
| 101 | 0 | |a eng | |
| 102 | |a CH | ||
| 135 | |a drcn ---uucaa | ||
| 181 | 0 | |a i |b e | |
| 182 | 0 | |a b | |
| 183 | 0 | |a cr |2 RDAcarrier | |
| 200 | 1 | |a Estimating Low- and High-Cyclic Fatigue of Polyimide-CF-PTFE Composite through Variation of Mechanical Hysteresis Loops |f S. V. Panin, A. A. Bogdanov, A. V. Eremin [et al.] | |
| 203 | |a Текст |c электронный |b визуальный | ||
| 283 | |a online_resource |2 RDAcarrier | ||
| 300 | |a Title screen | ||
| 320 | |a References: 38 tit | ||
| 330 | |a The fatigue properties of neat polyimide and the “polyimide + 10 wt.% milled carbon fibers + 10 wt.% polytetrafluoroethylene” composite were investigated under various cyclic loading conditions. In contrast to most of the reported studies, constructing of hysteresis loops was performed through the strain assessment using the non-contact 2D Digital Image Correlation method. The accumulation of cyclic damage was analyzed by calculating parameters of mechanical hysteresis loops. They were: (i) the energy losses (hysteresis loop area), (ii) the dynamic modulus (proportional to the compliance/stiffness of the material) and (iii) the damping capacity (calculated through the dissipated and total mechanical energies). On average, the reduction in energy losses reached 10–18% at the onset of fracture, whereas the modulus variation did not exceed 2.5% of the nominal value. The energy losses decreased from 20 down to 18 J/m3 (10%) for the composite, whereas they reduced from 30 down to 25 J/m3 (17%) for neat PI in the low-cycle fatigue mode. For high-cycle fatigue, energy losses decreased from 10 to 9 J/m3 (10%) and from 17 to 14 J/m3 (18%) for neat PI and composite, respectively. For this reason, the changes of the energy losses due to hysteresis are of prospects for the characterization of both neat PI and the reinforced PI-based composites | ||
| 336 | |a Текстовый файл | ||
| 461 | 1 | |t Materials |c Basel |n MDPI AG | |
| 463 | 1 | |t Vol. 15, iss. 13 |v Article number 4656, 17 p. |d 2022 | |
| 610 | 1 | |a polyimide | |
| 610 | 1 | |a milled carbon fibers (MCF) | |
| 610 | 1 | |a polytetrafluoroethylene (PTFE) | |
| 610 | 1 | |a polymer composite | |
| 610 | 1 | |a fatigue analysis | |
| 610 | 1 | |a электронный ресурс | |
| 610 | 1 | |a труды учёных ТПУ | |
| 701 | 1 | |a Panin |b A. V. |c physicist |c Professor of Tomsk Polytechnic University, doctor of physical and mathematical Sciences |f 1971- |g Alexey Viktorovich |9 17992 | |
| 701 | 1 | |a Bogdanov |b A. A. |g Aleksey Alekseevich | |
| 701 | 1 | |a Eremin |b A. V. |c specialist in the field of material science |c Engineer of Tomsk Polytechnic University |f 1990- |g Alexandr Vyacheslavovich |9 16760 | |
| 701 | 1 | |a Buslovich |b D. G. |g Dmitry Gennadjevich | |
| 701 | 1 | |a Alekseenko |b V. O. |g Vladislav Olegovich | |
| 801 | 0 | |a RU |b 63413507 |c 20260319 |g RCR | |
| 856 | 4 | 0 | |u https://doi.org/10.3390/ma15134656 |z https://doi.org/10.3390/ma15134656 |
| 942 | |c CF | ||