Investigation of the welded layer hardness at restoration of electric motor shafts; Journal of Applied Engineering Science; Vol. 23, iss 2

Investigation of the welded layer hardness at restoration of electric motor shafts; Journal of Applied Engineering Science; Vol. 23, iss 2

Detaylı Bibliyografya
Parent link:	Journal of Applied Engineering Science.— .— Belgrad: Institute for research and design in industry Vol. 23, iss 2.— 2025.— P. 322-329
Diğer Yazarlar:	Zharkevich O. M. Olga Mikhaylovna, Nurzhanova O. A. Oksana Amangeldyevna, Mukhitova A. Adeliya, Teliman I. Irina, Naboko E. Elena, Stukach O. V. Oleg Vladimirovich, Moyzes [Moises] B. B. Boris Borisovich
Özet:	Title screen The article is devoted to studying the influence of wire feed rate on the hardness of the welded layer during the restoration of electric motor shafts. The authors analyse the importance of optimal hardness to ensure the durability and reliability of the reconditioned parts. The paper considers various factors affecting the hardness of the welded layer, such as type of welding wire (AWS A5.18 ER70S-6, OK Tubrodur 35 G M, AWS A5.28 ER80S-G); cladding modes (feed rate, current, voltage); properties of the welded clad metal (fusion with the base, tendency to crack formation). Based on the conducted experiments, the optimal welding modes for each of the studied wires and the corresponding hardness values were determined. The obtained results allow us to conclude that the wire feed rate is one of the key parameters affecting the hardness of the welded layer Текстовый файл
Dil:	İngilizce
Baskı/Yayın Bilgisi:	2025
Konular:	hardfacing hardness voltage current wire feed rate электронный ресурс труды учёных ТПУ
Online Erişim:	https://doi.org/10.5937/jaes0-55948
Materyal Türü:	Elektronik Kitap Bölümü
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=685468

Benzer Materyaller

Improvement of Research Procedures into the Highly Rigid Welded Metal Using Thermal Microscopy Facilities; Materials Science Forum; Vol. 927 : Materials and Processing Technology II
Baskı/Yayın Bilgisi: (2018)

Improving the Reliability of the Protection of Electric Transport Networks; World Electric Vehicle Journal; Vol. 16, iss. 8
Baskı/Yayın Bilgisi: (2025)

Spatial stabilization of arc discharges in pulsed gas tungsten arc welding; Welding in the World; Vol. 68, iss. 9
Baskı/Yayın Bilgisi: (2024)

Calculation of a Switched Inductive-Capacitor Generator; Russian Electrical Engineering; Vol. 92, iss. 10
Yazar:: Nosov G. V. Gennady Vasilievich
Baskı/Yayın Bilgisi: (2021)

Calculation of the Parameters of a Two-Winding Transformer without a Magnetic Circuit; Russian Electrical Engineering; Vol. 91, iss. 6
Yazar:: Nosov G. V. Gennady Vasilievich
Baskı/Yayın Bilgisi: (2020)

The amplifier of unipolar pulses of the short range radar system; Bulletin of the Tomsk Polytechnic University; Vol. 309, № 4
Yazar:: Titov A. A.
Baskı/Yayın Bilgisi: (2006)

Corrections of Voltage Loss in Oxyhydrogen Fuel Cells; Batteries; Vol. 6, iss. 1
Yazar:: Lyu Jinzhe
Baskı/Yayın Bilgisi: (2020)

Microstructure and scratch behavior of TiB/Ti-6Al-4V composites fabricated by wire-feed electron beam additive manufacturing; Materials Letters; Vol. 405
Baskı/Yayın Bilgisi: (2026)

Numerical Simulation of Thermal Processes in Welding with Pulsed Electrode Wire Feeding; Materials Science Forum; Vol. 927 : Materials and Processing Technology II
Baskı/Yayın Bilgisi: (2018)

Microstructure and Phase Composition of 3D Printed Titanium Metal Matrix Composites Based on Ti-Al-V-Fe System and Reinforced with TiC Particles; Russian Physics Journal; Vol. 67, iss. 9
Baskı/Yayın Bilgisi: (2024)

Размыкатель сильноточных цепей постоянного тока с индуктивной нагрузкой; Известия Томского политехнического университета [Известия ТПУ]; Т. 324, № 4 : Техника и технологии в энергетике
Yazar:: Пустынников С. В. Сергей Владимирович
Baskı/Yayın Bilgisi: (2014)

Transformations of the Microstructure and Phase Compositions of Titanium Alloys during Ultrasonic Impact Treatment Part III: Combination with Electrospark Alloying Applied to Additively Manufactured Ti-6Al-4V Titanium Alloy; Metals; Vol. 13, iss. 5
Baskı/Yayın Bilgisi: (2023)

Hybrid real-time simulator of power system for advanced simulation of the FACTS and HVDC system based on Voltage Source Converter; 2nd International Conference on Systems and Informatics (ICSAI 2014)
Baskı/Yayın Bilgisi: (2014)

Deformation Behavior of Wrought and EBAM Ti-6Al-4V under Scratch Testing; Metals; Vol. 11, iss. 11
Baskı/Yayın Bilgisi: (2021)

Моделирование и идентификация узлов нагрузки с нелинейными вольтамперными характеристиками по данным измерений; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 328, № 6
Yazar:: Харлов Н. Н. Николай Николаевич
Baskı/Yayın Bilgisi: (2017)

Calculation of Uniform Corrosion Current Density of Iron in Hydrochloric Acid Solutions based on the Principle of Maximum Entropy Production Rate Applied to Literature Data; Protection of Metals and Physical Chemistry of Surfaces; Vol. 54, iss. 4
Baskı/Yayın Bilgisi: (2018)

Use of the sampled electrical engineering device at diagnosing elements in electric systems; Bulletin of the Tomsk Polytechnic University; Vol. 311, № 4 : Power engineering
Yazar:: Goldshtein E. I.
Baskı/Yayın Bilgisi: (2007)

Effect of Ultrasonic Impact Treatment on Microstructure and Fatigue Life of 3D Printed Ti–6Al–4V Titanium Alloy; Physics of Metals and Metallography; Vol. 124, iss. 10
Baskı/Yayın Bilgisi: (2023)

Enhancing Microhardness and Corrosion Resistance of Anodic Oxides Grown on Hypoeutectic Al–Si Alloys Pretreated by Low-Energy High-Current Electron Beams; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 18, iss. 5
Baskı/Yayın Bilgisi: (2024)

The Effect of Heat Treatment on the Microstructure and Phase Composition of Wrought and 3D-Printed Ti–5Al–3Mo–1V Titanium Alloy Samples; Journal of Surface Investigation: X-ray, Synchrotron and Neutron Techniques; Vol. 17, Suppl. 1
Baskı/Yayın Bilgisi: (2023)

Study of Melting Methods by Electric Resistance Welding of Rails; Metals; Vol. 12, iss. 12
Baskı/Yayın Bilgisi: (2022)

Multi-Pass Laser and Hybrid Laser-Arc Narrow-Gap Welding of Steel Butt Joints; Materials Science Forum; Vol. 927 : Materials and Processing Technology II
Baskı/Yayın Bilgisi: (2018)

Измерение внутреннего диаметра труб при помощи вихретокового метода контроля; Ресурсосберегающие технологии в контроле, управлении качеством и безопасности
Yazar:: Мелехина Е. С. Екатерина Сергеевна
Baskı/Yayın Bilgisi: (2024)

Strengthening of Metallurgical Equipment Parts by Plasma Surfacing in Nitrogen Atmosphere; Metallurgist; Vol. 65, iss. 11-12
Baskı/Yayın Bilgisi: (2022)

The role of surface defects in the charge transport in organic solar cells based on oxidized indium thin films; Surfaces and Interfaces; Vol. 31
Baskı/Yayın Bilgisi: (2022)

The development of the complex of pulse-modulation amplifiers of voltage and current; Przeglad Elektrotechniczny; Vol. 95, iss. 11
Baskı/Yayın Bilgisi: (2019)

Assessment of dynamic transformer rating, considering current and temperature limitations; International Journal of Electrical Power & Energy Systems; Vol. 129
Baskı/Yayın Bilgisi: (2021)

Features of high-frequency capacitor discharge combustion process in media with disperse phase; Bulletin of the Tomsk Polytechnic University; Vol. 311, № 2
Yazar:: Lucenko (Lutsenko) Yu. Yu. Yuri Yurievich
Baskı/Yayın Bilgisi: (2007)

Quality of Metal Deposited Flux Cored Wire with the System Fe-C-Si-Mn-Cr-Mo-Ni-V-Co; Key Engineering Materials; Vol. 736 : Materials and their Application
Baskı/Yayın Bilgisi: (2017)

Improvement of a powerful ion Br - Diode parameters by changing the distribution of the magnetic flux in the anode – cathode gap; Vacuum; Vol. 176
Baskı/Yayın Bilgisi: (2020)

Obtaining neodymium from melts by electrolysis; Bulletin of the Tomsk Polytechnic University; Vol. 311, № 3
Yazar:: Grebnev V. A.
Baskı/Yayın Bilgisi: (2007)

Additive Manufacturing of Metal Products via Filler Wire Arc Welding (Review); Materials Science Forum; Vol. 1064
Baskı/Yayın Bilgisi: (2022)

A Method for Endurance Testing of Enameled Round and Rectangular Wires for Motors Controlled by SiC-based Inverters; IEEE Transactions on Dielectrics and Electrical Insulation; Vol. 28, iss. 6
Baskı/Yayın Bilgisi: (2021)

The Appliction of Modified Gausse-Newton Method for Improving Accuracy of Regime Parameters State Estimation and Control Action Adjusment in The Centralized Emergancy Control System; Relay Protection and Automation (RPA 2020)
Yazar:: Batseva N. L. Natalya Lenmirovna
Baskı/Yayın Bilgisi: (2020)

The second order polynomial load model impact on stability of the synchronous motor; Industrial Engineering, Applications and Manufacturing (ICIEAM)
Yazar:: Batseva N. L. Natalya Lenmirovna
Baskı/Yayın Bilgisi: (2016)

Determining the equivalent circuit parameters of transmission lines, reactors, power resistors and capacitor banks by the arrays of instantaneous currents and voltages; Bulletin of the Tomsk Polytechnic University; Vol. 311, № 4 : Power engineering
Yazar:: Dzhumik D. V.
Baskı/Yayın Bilgisi: (2007)

On the issue of modeling non-sinusoidal modes of distribution networks; 11th International Forum on Strategic Technology (IFOST 2016); Pt. 2
Baskı/Yayın Bilgisi: (2016)

Technological Improvement of Surfacing of Parts of Hammer Crushers Used in Coke-Chemical Industry; Materials Science Forum; Vol. 927 : Materials and Processing Technology II
Baskı/Yayın Bilgisi: (2018)

Influence of the Cobalt Additive on the Flux Cored Wire of System Fe-C-Si-Mn-Cr-Ni-Mo-V; Key Engineering Materials; Vol. 736 : Materials and their Application
Baskı/Yayın Bilgisi: (2017)

Двухфазный повышающий преобразователь с мягкой коммутацией транзисторов и особенности его динамических свойств; Известия Томского политехнического университета [Известия ТПУ]; Т. 324, № 4 : Техника и технологии в энергетике
Baskı/Yayın Bilgisi: (2014)