$In-situ X-ray diffraction study of hydrogen-induced phase transformation in wire-feed electron-beam additive manufactured Ti-6Al-4V alloy; Journal of Alloys and Compounds; Vol. 1045$

In-situ X-ray diffraction study of hydrogen-induced phase transformation in wire-feed electron-beam additive manufactured Ti-6Al-4V alloy; Journal of Alloys and Compounds; Vol. 1045

Λεπτομέρειες βιβλιογραφικής εγγραφής
Parent link:	Journal of Alloys and Compounds.— .— Amsterdam: Elsevier Science Publishing Company Inc. Vol. 1045.— 2025.— Article number 184584, 9 p.
Άλλοι συγγραφείς:	Kamelina K. D. Kristina Dmitrievna, Panin A. V. Alexey Viktorovich, Syrtanov M. S. Maksim Sergeevich, Kashkarov E. B. Egor Borisovich
Περίληψη:	In situ X-ray diffraction studies of Ti-6Al-4V titanium alloy samples obtained by casting and wire electron beam additive manufacturing (EBAM) are carried out during heating to 450°C and subsequent gas-phase hydrogenation. A different behavior of decreasing the residual stresses, micro-distortions, and increasing the lattice parameters of the α- and β-phases of the cast and EBAM samples demonstrates during heating to 450 °C. The hydrogen content in the cast sample hydrogenated at 450 °C for 55 min does not exceed 0.03 wt%, whereas it reaches 3.4 wt% in the EBAM sample under the same conditions. The XRD establishes that the following phase transformations occur in the process of hydrogenation of the EBAM Ti-6Al-4V sample: α+ β → α+ β+ α" → α+ β+ α"+ort → β+ α''+ort → β +ort+cub → β+cub, where ort is TiH0.71, cub is TiH2. Transmission electron microscopy shows the regularities of hydride phase formation in hydrogenated EBAM sample Текстовый файл AM_Agreement
Γλώσσα:	Αγγλικά
Έκδοση:	2025
Θέματα:	Electron beam additive manufacturing Ti-6Al-4V titanium alloy Titanium hydride Transmission electron microscopy In situ XRD труды учёных ТПУ электронный ресурс
Διαθέσιμο Online:	https://doi.org/10.1016/j.jallcom.2025.184584
Μορφή:	Ηλεκτρονική πηγή Κεφάλαιο βιβλίου
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=683314

Παρόμοια τεκμήρια

In Situ High-Temperature Synchrotron X-ray Studies of Microstructure and Phase Composition of Additively Fabricated Ti–6Al–4V/TiC Metal Matrix Composite; Journal of Surface Investigation: X-ray, Synchrotron and Neutron Techniques; Vol. 19, iss. 4
Έκδοση: (2025)

The Microstructural and Phase Evolution of the 3D Printed Ti-6Al-4V Alloy during Mechanical Loading; Physics of Metals and Metallography; Vol. 124, iss. 2
Έκδοση: (2023)

Titanium Carbide Coating for Hafnium Hydride Neutron Control Rods: In Situ X-ray Diffraction Study; Coatings; Vol. 13, iss. 12
Έκδοση: (2023)

Microstructural Transformation and Enhanced Strength of Wire-Feed Electron-Beam Additive Manufactured Ti–6Al–4V Alloy Induced by High-Pressure Torsion; Advanced Engineering Materials; Vol. 26, iss. 4
Έκδοση: (2024)

Microstructure and Phase Composition of VT1-0, VT6, and VT14 Titanium Alloys Produced by Wire-Feed Electron-Beam Additive Manufacturing; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 16, iss. 6
Έκδοση: (2022)

Change in the Phase Composition and Lattice Parameters of the Solid Solution Based on a-Ti in the Surface Layers of the Ti–6Al–4V Alloy Subjected to Electron-Beam Treatment; Physics of Metals and Metallography; Vol. 121, iss. 2
από: Perevalova O. B. Olga Borisovna
Έκδοση: (2020)

Laboratory X-ray Diffraction Complex for In Situ Investigations of Structural Phase Evolution of Materials under Gaseous Atmosphere; Metals; Vol. 10, iss. 4
Έκδοση: (2020)

Effect of Conditions of the Pulsed Plasma-chemical Synthesis on Physicochemical Properties of the CuxOy/TiO2 Nanocomposite; Current Nanomaterials; Vol. 7, iss. 3
Έκδοση: (2022)

Transformations of the Microstructure and Phase Compositions of Titanium Alloys during Ultrasonic Impact Treatment. Part I. Commercially Pure Titanium; Metals; Vol. 11, iss. 4
Έκδοση: (2021)

Influence of beam current on microstructure of electron beam melted Ti-6Al-4V alloy; Progress in Natural Science: Materials International; Vol. 29, iss. 4
Έκδοση: (2019)

Comparative Analysis of Weld Microstructure in Ti-6Al-4V Samples Produced by Rolling and Wire-Feed Electron Beam Additive Manufacturing; Physical Mesomechanics; Vol. 26, iss. 6
Έκδοση: (2023)

The Effect of Heat Treatment on the Microstructure and Phase Composition of Wrought and 3D-Printed Ti–5Al–3Mo–1V Titanium Alloy Samples; Journal of Surface Investigation: X-ray, Synchrotron and Neutron Techniques; Vol. 17, Suppl. 1
Έκδοση: (2023)

Effect of Ultrasonic Impact Treatment on Structural Phase Transformations in Ti-6Al-4V Titanium Alloy; Physical Mesomechanics; Vol. 25, iss. 3
Έκδοση: (2022)

Swift heavy ion induced phase transformations in partially stabilized ZrO2; Radiation Physics and Chemistry; Vol. 192
Έκδοση: (2022)

Effect of Heat Input on the Microstructure and Phase Composition of Additively Manufactured Ti–6Al–4V Alloy; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 18, iss. 6
από: Kamelina K. D. Kristina Dmitrievna
Έκδοση: (2024)

Influence of manufacturing parameters on microstructure and hydrogen sorption behavior of electron beam melted titanium Ti-6Al-4V alloy; Materials; Vol. 11, iss. 5
Έκδοση: (2018)

Рентгеноструктурные исследования аддитивно полученного образца титанового сплава Ti-6Al-4V при газофазном наводораживании; Перспективы развития фундаментальных наук; Т. 1 : Физика
από: Камелина К. Д. Кристина Дмитриевна
Έκδοση: (2025)

Metallurgy of a Ti–Au alloy synthesized by controlled electric resistance fusion; Intermetallics; Vol. 127
Έκδοση: (2020)

Microstructure and Phase Composition of 3D Printed Titanium Metal Matrix Composites Based on Ti-Al-V-Fe System and Reinforced with TiC Particles; Russian Physics Journal; Vol. 67, iss. 9
Έκδοση: (2024)

The Effect of Electron Beam Welding on the Microstructure and Microhardness of 3D-Printed Products from Titanium Alloy Ti-6Al-4V; Physics of Metals and Metallography; Vol. 122, iss. 2
Έκδοση: (2021)

Beam Current Effect on Microstructure and Properties of Electron-Beam-Melted Ti-6Al-4V Alloy; Journal of Materials Engineering and Performance; Vol. 28, iss. 10
Έκδοση: (2019)

Methane conversion into aromatic hydrocarbons over Ag-Mo/ZSM-5 catalysts; Kinetics and Catalysis; Vol. 52, iss. 3
Έκδοση: (2011)

Phase transformations in ferrites during radiation-thermal sintering; Eurasian Physical Technical Journal; Vol. 17, № 1 (33)
Έκδοση: (2020)

Effect of Ultrasonic Impact Treatment on Microstructure and Fatigue Life of 3D Printed Ti–6Al–4V Titanium Alloy; Physics of Metals and Metallography; Vol. 124, iss. 10
Έκδοση: (2023)

Hydrogen-Induced Phase Transformation and Microstructure Evolution for Ti-6Al-4V Parts Produced by Electron Beam Melting; Metals; Vol. 8, iss. 5
Έκδοση: (2018)

Improvement of Mechanical Properties and Adhesion of Ti-Al-Si-N Coatings by Alloying with Ta; Lubricants; Vol. 10 iss. 8
Έκδοση: (2022)

Effect of the Beam Current during the Electron-Beam Melting of Titanium Alloy Ti-6Al-4V on the Structural Features and Phase Transitions in Gas-Phase Hydrogenation; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 13, No. 3
Έκδοση: (2019)

Hydrogen sorption by Ni-coated titanium alloy VT1-0; International Journal of Hydrogen Energy; Vol. 42, iss. 22
Έκδοση: (2017)

In situ study of phase transformations in electron beam additive manufactured Ti-6Al-4 V titanium alloy by high temperature synchrotron X-ray diffraction and TEM; Journal of Alloys and Compounds; Vol. 917
από: Perevalova O. B. Olga Borisovna
Έκδοση: (2022)

Особенности формирования сварного шва при имитации электронно-лучевой сварки толстостенных образцов ВТ6, полученных электронно-лучевой аддитивной; Перспективы развития фундаментальных наук; Т. 1 : Физика
από: Яхин А. Альберт
Έκδοση: (2025)

Модификация микроструктуры в процессе ультразвуковой ударной электроискровой обработки сварных швов образцов ВТ6, полученных прокаткой и электронно-лучевой аддитивной технологией; Перспективы развития фундаментальных наук; Т. 1 : Физика
από: Яхин А. Альберт
Έκδοση: (2025)

Orientation of Nickel-Based Alloy after Thermal Treatment; AIP Conference Proceedings; Vol. 1909 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2017 (AMHS’17)
Έκδοση: (2017)

In situ synthesis of a binary Ti–10at% Nb alloy by electron beam melting using a mixture of elemental niobium and titanium powders; Journal of Materials Processing Technology; Vol. 282
Έκδοση: (2020)

The Effect of Irradiation of a Titanium Alloy of the Ti–6Al–4V–Н System with Pulsed Electron Beams on Its Creep; Russian Physics Journal; Vol. 63, iss. 6
Έκδοση: (2020)

Modification of Ti-6Al-4V alloy element and phase composition by compression plasma flows impact; Surface and Coatings Technology; Vol. 355
Έκδοση: (2018)

Grain-boundary diffusion of titanium in Zr-1 wt.%Nb alloy under irradiation with a pulsed electron beam; Russian Physics Journal; Vol. 66, No. 11
Έκδοση: (2024)

Formation of the structure and properties of the near-surface layer in alloys of the Ti–6Al–4V–H system under irradiation with a pulsed electron beam; Russian Physics Journal; Vol. 66, No. 2
Έκδοση: (2023)

Influence of anisotropy properties and structural inhomogeneity on elasticity and fracture of titanium alloys produced by electron-beam melting; International Journal of Advanced Manufacturing Technology; Vol. 135
Έκδοση: (2025)

The High-Temperature In Situ Synchrotron Study of the Structural-Phase Transformations in 3D-Printed Ti–6Al–4V and Ti–5Al–3Mo–V Titanium Alloys; Physics of Metals and Metallography; Vol. 125, iss. 9
Έκδοση: (2024)

The Structure and Properties of Microcrystalline and Submicrocrystalline Titanium Alloy VT1-0 in the Area of the Electron Beam Welding Seam; Russian Physics Journal; Vol. 60, iss. 6
Έκδοση: (2017)