Electron Beam Impact on Microstructure and Microhardness of Ti–6Al–4V Titanium Alloy Produced by Wire Electron-Beam Additive Manufacturing Technology and Selective Laser Alloying at Simulation of Electronic-Beam Welding; Physics of Metals and Metallography; Vol. 125, iss. 7

Electron Beam Impact on Microstructure and Microhardness of Ti–6Al–4V Titanium Alloy Produced by Wire Electron-Beam Additive Manufacturing Technology and Selective Laser Alloying at Simulation of Electronic-Beam Welding; Physics of Metals and Metallography; Vol. 125, iss. 7

Détails bibliographiques
Parent link:	Physics of Metals and Metallography.— .— New York: Springer Science+Business Media LLC Vol. 125, iss. 7.— 2024.— P. 790-796
Autres auteurs:	Perevalova O. B. Olga Borisovna, Panin A. V. Alexey Viktorovich, Kazachenok M. S. Marina Sergeevna, Martynov S. A. Sergey Aleksandrovich
Résumé:	Title screen The microstructure and phase composition of Ti–6Al–4V alloy specimens produced by wire electron-beam additive manufacturing (EBAM) technology and selective laser melting (SLM) method after exposure to an electron beam, simulating electron-beam welding, have been investigated by X-ray diffraction analysis, optical metallography, and transmission electron microscopy. In the electron beam exposure zone of SLM specimens, in contrast to EBAM specimens, it was observed that the transverse dimensions of anisotropic primary β grains and α/α′ phase plates increased and inside α/α′ phase plates, submicrocrystalline α phase grains and nanocrystalline α′′ phase were formed. The different character of microstructure and, accordingly, microhardness changes in the weld zone and heat-affected zone in comparison with the base metal is caused by the different cooling rate of the melt bath in the weld zones of EBAM and SLM specimens. In the SLM specimen, the cooling rate of the melt bath is less than that observed in the EBAM specimen. This discrepancy can be attributed to the fact that due to the finer needle-like α′ martensitic structure, the thermal conductivity in the base metal of the SLM sample is less than that in the base metal of the EBAM sample Текстовый файл AM_Agreement
Langue:	anglais
Publié:	2024
Sujets:	электронный ресурс труды учёных ТПУ titanium alloy wire electron-beam additive manufacturing technology selective laser melting X‑ray diffraction analysis phase composition microstructure micro-deformation of α phase lattice residual elastic macrostresses microhardness
Accès en ligne:	https://doi.org/10.1134/S0031918X24600842
Format:	Électronique Chapitre de livre
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=680819

Documents similaires

Increasing the Fatigue Durability of an 3D-Printed Ti-6Al-4V Alloy Electron-Beam Welded Joint by Ultrasonic Electropulsing Shock Treatment; Physics of Metals and Metallography; Vol. 123, iss. 12
Publié: (2022)

In Situ Synchrotron Study of the Phase Transformations in Ti-5.7Al-1.6V-3Mo Titanium Alloy at High Temperature; Journal of Materials Engineering and Performance; Vol. 33, iss. 19
par: Perevalova O. B. Olga Borisovna
Publié: (2024)

The Effect of Electropulsing-Assisted Ultrasonic Impact Treatment on the Microstructure, Phase Composition, and Microhardness of Electron-Beam-Welded 3D Printed Ti-6Al-4V Alloy; Physics of Metals and Metallography; Vol. 123, iss. 9
Publié: (2022)

In situ study of phase transformations in electron beam additive manufactured Ti-6Al-4 V titanium alloy by high temperature synchrotron X-ray diffraction and TEM; Journal of Alloys and Compounds; Vol. 917
par: Perevalova O. B. Olga Borisovna
Publié: (2022)

Microstructure and Phase Composition of VT1-0, VT6, and VT14 Titanium Alloys Produced by Wire-Feed Electron-Beam Additive Manufacturing; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 16, iss. 6
Publié: (2022)

The Structure and Properties of Microcrystalline and Submicrocrystalline Titanium Alloy VT1-0 in the Area of the Electron Beam Welding Seam; Russian Physics Journal; Vol. 60, iss. 6
Publié: (2017)

Hydrogen effect on Ti-6.5Al-3.5Mo-1.5Zr-0.3Si parts produced by electron beam melting; International Journal of Hydrogen Energy; Vol. 44, iss. 55
Publié: (2019)

Effect of Ultrasonic Impact Treatment on Microstructure and Fatigue Life of 3D Printed Ti–6Al–4V Titanium Alloy; Physics of Metals and Metallography; Vol. 124, iss. 10
Publié: (2023)

Structure and properties of welding joints of 1370 aluminum alloy obtained by electron-beam welding; Russian Physics Journal; Vol. 68, iss. 2
par: Solov’ev V. V. Vasily Vladimirovich
Publié: (2025)

The Effect of Electron Beam Welding on the Microstructure and Microhardness of 3D-Printed Products from Titanium Alloy Ti-6Al-4V; Physics of Metals and Metallography; Vol. 122, iss. 2
Publié: (2021)

Influence of heat treatment modes on the structure and property of the Ti–4Al–3V titanium alloy manufactured by the wire electron beam additive technology; Russian Physics Journal; Vol. 68, iss. 4
Publié: (2025)

The Effect of Heat Treatment on the Microstructure and Phase Composition of Wrought and 3D-Printed Ti–5Al–3Mo–1V Titanium Alloy Samples; Journal of Surface Investigation: X-ray, Synchrotron and Neutron Techniques; Vol. 17, Suppl. 1
Publié: (2023)

Effect of Surface Electropulsing Assisted Ultrasonic Impact Treatment on the Microstructure, Phase Composition, and Microhardness of 3D Printed Ti-6Al-4V Alloy; Physics of Metals and Metallography; Vol. 122, iss. 7
par: Perevalova O. B. Olga Borisovna
Publié: (2021)

Electron-Beam Welding - Structural-Phase State and Microhardnes in the Weld Zone in a Submicrocrystalline Titanium Alloy Grade2; Materials Science Forum; Vol. 906 : Materials and Processing Technology
Publié: (2017)

Beam Current Effect on Microstructure and Properties of Electron-Beam-Melted Ti-6Al-4V Alloy; Journal of Materials Engineering and Performance; Vol. 28, iss. 10
Publié: (2019)

Microstructural Transformation and Enhanced Strength of Wire-Feed Electron-Beam Additive Manufactured Ti–6Al–4V Alloy Induced by High-Pressure Torsion; Advanced Engineering Materials; Vol. 26, iss. 4
Publié: (2024)

The Special Features of the Phase Formation and Distribution in the Titanium Nickelide Surface Layers Treated by Electron Beams; Russian Physics Journal; Vol. 58, iss. 5
Publié: (2015)

Effect of surface modification by a high-current electron beam on the kinetics of the structure of hydride phases in titanium; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 9, iss. 2
par: Timchenko N. A. Nikolay Alekseevich
Publié: (2015)

The structure - phase state and microhardness of the surface layer of the VT1-0 titanium alloys treated by copper ions; Vacuum; Vol. 149
Publié: (2018)

Concentration-Dependent Transformation Plasticity Effect During Hydrogenation of Technically Pure Titanium Irradiated with an Electron Beam; Russian Physics Journal; Vol. 61, iss. 11
par: Perevalova O. B. Olga Borisovna
Publié: (2019)

Effect of Heat Input on the Microstructure and Phase Composition of Additively Manufactured Ti–6Al–4V Alloy; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 18, iss. 6
par: Kamelina K. D. Kristina Dmitrievna
Publié: (2024)

Effect of Irradiation with a Pulsed Electron Beam on the Defect Structure Formation and the Properties of the Surface Layer of Zr–Nb–H System Alloys; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 17
Publié: (2023)

The Microstructural and Phase Evolution of the 3D Printed Ti-6Al-4V Alloy during Mechanical Loading; Physics of Metals and Metallography; Vol. 124, iss. 2
Publié: (2023)

Hydrogen-Induced Phase Transformation and Microstructure Evolution for Ti-6Al-4V Parts Produced by Electron Beam Melting; Metals; Vol. 8, iss. 5
Publié: (2018)

Effect of the Beam Current during the Electron-Beam Melting of Titanium Alloy Ti-6Al-4V on the Structural Features and Phase Transitions in Gas-Phase Hydrogenation; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 13, No. 3
Publié: (2019)

Change in the Phase Composition and Lattice Parameters of the Solid Solution Based on a-Ti in the Surface Layers of the Ti–6Al–4V Alloy Subjected to Electron-Beam Treatment; Physics of Metals and Metallography; Vol. 121, iss. 2
par: Perevalova O. B. Olga Borisovna
Publié: (2020)

Surface Modification of the EBM Ti-6Al-4V Alloy by Pulsed Ion Beam; Metals; Vol. 11, iss. 3
Publié: (2021)

Structure and Lattice Strains in the Surface Сr–Mn–N Steel Layer Formed by a Combination of Friction and Electron-Beam Treatments; Physics of Metals and Metallography; Vol. 120, iss. 11
Publié: (2019)

The Synthesis Method of Intermetallic Alloys Based on Ti–Cr with C14 and C36 Laves Phases for Hydrogen Storage; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 13, iss. 1
Publié: (2019)

Effects of Water Cooling on the Microstructure of Electron Beam Additive-Manufactured Ti-6Al-4V; Metals; Vol. 11, iss. 11
Publié: (2021)

Microstructure Formation and Mechanical Properties of Metastable Titanium-Based Gradient Coating Fabricated via Intense Pulse Ion Beam Melt Mixing; Materials; Vol. 16, iss. 8
Publié: (2023)

The High-Temperature In Situ Synchrotron Study of the Structural-Phase Transformations in 3D-Printed Ti–6Al–4V and Ti–5Al–3Mo–V Titanium Alloys; Physics of Metals and Metallography; Vol. 125, iss. 9
Publié: (2024)

Microstructure, microhardness and chemical composition of a detail obtained by electro-arc surfacing on a hardware-software complex of a delta layout; Structural Integrity and Life; Vol. 24, № 3
Publié: (2024)

Surface Vaporization of High-Strength Aluminum Alloy During Electron-Beam Welding; Russian Physics Journal; Vol. 65, iss. 3
Publié: (2022)

High Chromium Steel Modification by the Intense Discrete Electron Beam: Structure and Properties; Key Engineering Materials; Vol. 781 : Radiation-Thermal Effects and Processes in Inorganic Materials
Publié: (2018)

Transformations of the Microstructure and Phase Compositions of Titanium Alloys during Ultrasonic Impact Treatment Part III: Combination with Electrospark Alloying Applied to Additively Manufactured Ti-6Al-4V Titanium Alloy; Metals; Vol. 13, iss. 5
Publié: (2023)

The Influence of Dimesions and Phase State of Structural Elements on Mechanical Properties of Binary Alloys of the Ti–Nb and Zr–Nb Systems; Russian Physics Journal; Vol. 61, iss. 10
Publié: (2019)

Thermal Stability of Structure and Properties of the Surface Layer of Instrumental Steel Alloyed with Zirconium and Silicon Atoms under the Action of Compression Plasma Flows; Inorganic Materials: Applied Research; Vol. 9, iss. 5
Publié: (2018)

Structural-phase state and mechanical properties of submicrocrystalline titanium alloy Ti-6Al-4V obtained with use of reversible hydrogen alloying; Bulletin of the Tomsk Polytechnic University; Vol. 311, № 2
par: Grabovetskaya G. P. Galina Petrovna
Publié: (2007)

Effect of the Lattice Curvature of Ti-6Al-4V Titanium Alloy on Their Fatigue Life and Fracture Toughness; Physical Mesomechanics; Vol. 23, iss. 5
Publié: (2020)