Effects of preheating and slow cooling stages in small-scale resistance spot welding of the Ti-2Al-1Mn alloy
| Parent link: | International Journal of Advanced Manufacturing Technology.— .— New York: Springer Science+Business Media LLC. Vol. 128, iss/ 7-8.— 2023.— P. 3011-3024 |
|---|---|
| Další autoři: | Butsykin S. E. Sergei Eduardovich, Slobodyan M. S. Mikhail Stepanovich, Strelkova I. L. Irina Leonidovna, Klimenov V. A. Vasily Aleksandrovich, Elkin M. A. Maxim Aleksandrovich, Gordynets A. S. Anton Sergeevich, Kiselev A. S. Aleksey Sergeevich |
| Shrnutí: | Title screen The aim of the study was to improve the stability of the quality of joints of two Ti-2%Al-1%Mn alloy plates with a thickness of 0.5 mm, obtained by resistance spot welding. The determined range of the optimal energy parameters (within the current amplitudes of 3.3–4.8 kA and the pulse durations of 8–16 ms) made it possible to form nuggets of sufficient diameters without expulsions in most cases. The implemented preheating stage (the pulse with the amplitude of ~ 1 kA and the duration of ~ 3 ms) reduced the dispersions of both nugget diameters (by 60%) and peak loads (by a factor of 2), while it increased the average fracture energy by 30% and the mean peak load by 8%. The simultaneously applied both preheating and slow cooling stages decreased the dispersion of the nugget diameters by 160% and enhanced the average both fracture energy by 48% and peak load by 15% in comparison with those for the rectangular pulse. Since no fundamental differences in the microstructure and phase composition were observed in the nuggets, lowering residual stresses was suggested as the most probable reason for such results Текстовый файл AM_Agreement |
| Vydáno: |
2023
|
| Témata: | |
| On-line přístup: | https://doi.org/10.1007/s00170-023-12110-9 |
| Médium: | Elektronický zdroj Kapitola |
| KOHA link: | https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=680144 |
Podobné jednotky
Advances in small-scale resistance spot welding of the Ni-15 %Fe-4 %Mo-1 %Mn permalloy in the production of low-noise ring cores for fluxgate magnetometers
Vydáno: (2024)
Vydáno: (2024)
Optimization of Welding Parameters for Small-Scale Resistance Spot Welding of Zirconium Alloys
Autor: Slobodyan M. S. Mikhail Stepanovich
Vydáno: (2019)
Autor: Slobodyan M. S. Mikhail Stepanovich
Vydáno: (2019)
Evaluation of the reliability of resistance spot welding control via on-line monitoring of dynamic resistance
Vydáno: (2022)
Vydáno: (2022)
Effects of Electrode Degradation on Properties of Small-Scale Resistance Spot Welded Joints of E110 Alloy
Autor: Kiselev A. S. Aleksey Sergeevich
Vydáno: (2019)
Autor: Kiselev A. S. Aleksey Sergeevich
Vydáno: (2019)
Prediction and stabilization of initial resistance between electrodes for small-scale resistance spot welding
Autor: Akbolatov E. Z. Eldos Zhannuruly
Vydáno: (2019)
Autor: Akbolatov E. Z. Eldos Zhannuruly
Vydáno: (2019)
Dynamic resistance signal–based wear monitoring of resistance spot welding electrodes
Vydáno: (2024)
Vydáno: (2024)
Assessing Electrode Characteristics in Continuous Resistance Spot Welding of BH 340 Steel Based on Dynamic Resistance
Vydáno: (2023)
Vydáno: (2023)
Comparative Analysis of Weld Microstructure in Ti-6Al-4V Samples Produced by Rolling and Wire-Feed Electron Beam Additive Manufacturing
Vydáno: (2023)
Vydáno: (2023)
Quality of Metal Deposited Flux Cored Wire with the System Fe-C-Si-Mn-Cr-Mo-Ni-V-Co
Vydáno: (2017)
Vydáno: (2017)
Computer system for measurement of welding process parameters
Autor: Muravyov (Murav’ev) S. V. Sergey Vasilyevich
Vydáno: (2006)
Autor: Muravyov (Murav’ev) S. V. Sergey Vasilyevich
Vydáno: (2006)
Stability of MMA welding with protective coatings
Vydáno: (2020)
Vydáno: (2020)
Electron Beam Welding of Dissimilar Materials
Autor: Frolov V. A.
Vydáno: (2017)
Autor: Frolov V. A.
Vydáno: (2017)
Effect of Protective Coatings in Welded Constructions on Welding Stability and Electrode Metal Transfer into a Weld Pool in MMA
Vydáno: (2020)
Vydáno: (2020)
Модификация микроструктуры в процессе ультразвуковой ударной электроискровой обработки сварных швов образцов ВТ6, полученных прокаткой и электронно-лучевой аддитивной технологией
Autor: Яхин А. Альберт
Vydáno: (2025)
Autor: Яхин А. Альберт
Vydáno: (2025)
A Study of Transient Processes in a High-Current Vacuum-Arc Anode Spot Using High-Speed Spectroscopy and Videorecording
Vydáno: (2021)
Vydáno: (2021)
Pulsed laser welding of Zr1%Nb alloy
Autor: Yolkin M. A. Maksim Aleksandrovich
Vydáno: (2019)
Autor: Yolkin M. A. Maksim Aleksandrovich
Vydáno: (2019)
Research of the current type effect and its modulation algorithm on the performance of welded joints
Vydáno: (2020)
Vydáno: (2020)
Improvement of Research Procedures into the Highly Rigid Welded Metal Using Thermal Microscopy Facilities
Vydáno: (2018)
Vydáno: (2018)
Spatial stabilization of arc discharges in pulsed gas tungsten arc welding
Vydáno: (2024)
Vydáno: (2024)
Applying Digital Image Correlation Technique for Studying the Growth of a Fatigue Crack in VT23 Titanium Alloy Welded Joints
Vydáno: (2019)
Vydáno: (2019)
Effect of ultra-disperse powder in electrode coating on properties of welds in MMA welding
Vydáno: (2020)
Vydáno: (2020)
Technological Improvement of Surfacing of Parts of Hammer Crushers Used in Coke-Chemical Industry
Vydáno: (2018)
Vydáno: (2018)
Hydrogenation Behavior of Cr-Coated Resistance Upset Welds of E110 Zirconium Alloy
Vydáno: (2023)
Vydáno: (2023)
Effect of ultrasound on interface morphology and strength of titanium and aluminum alloys joints produced by friction stir welding
Vydáno: (2023)
Vydáno: (2023)
Coulomb explosion of "hot spot"
Vydáno: (2016)
Vydáno: (2016)
The Structure and Properties of Microcrystalline and Submicrocrystalline Titanium Alloy VT1-0 in the Area of the Electron Beam Welding Seam
Vydáno: (2017)
Vydáno: (2017)
The Formation of One-Piece Bimetallic Joint Made of X6CrNiTi18-10 Steel and 36CrNiTiAl Alloy
Autor: Svyazhina N. V.
Vydáno: (2016)
Autor: Svyazhina N. V.
Vydáno: (2016)
In Situ Studies of Strain Fields in Titanium Welds under Tensile Loads by Digital Image Correlation Method
Vydáno: (2022)
Vydáno: (2022)
Ultrasonic-assisted aging in friction stir welding on Al-Cu-Li-Mg aluminum alloy
Vydáno: (2017)
Vydáno: (2017)
Scale levels of quasi-static and dynamic fracture behavior of Ti-6Al-4V parts built by various additive manufacturing methods
Vydáno: (2020)
Vydáno: (2020)
Method for basic measurement adjustment of commutator profiles
Autor: Borovikov Y. S. Yuri Sergeevich
Vydáno: (2007)
Autor: Borovikov Y. S. Yuri Sergeevich
Vydáno: (2007)
Improving the Reliability of the Protection of Electric Transport Networks
Vydáno: (2025)
Vydáno: (2025)
Formation features of microstructure, elemental and phase compositions of the C-Cr-Mn-V-Fe coatings under conditions of electron beam (EB) Surfacing in vacuum
Autor: N. K. Nina Konstantinovna Galchenko
Vydáno: (2024)
Autor: N. K. Nina Konstantinovna Galchenko
Vydáno: (2024)
Calculation of the Parameters of a Two-Winding Transformer without a Magnetic Circuit
Autor: Nosov G. V. Gennady Vasilievich
Vydáno: (2020)
Autor: Nosov G. V. Gennady Vasilievich
Vydáno: (2020)
Effect of energy parameters of pulsed laser welding of Zr-1%Nb alloy on metal contamination with gases and properties of welds
Autor: Slobodyan M. S. Mikhail Stepanovich
Vydáno: (2019)
Autor: Slobodyan M. S. Mikhail Stepanovich
Vydáno: (2019)
Influence of SiO2 micro-particles onto microstructure, mechanical properties and wear resistance of uhmwpe based composite under dry sliding friction
Vydáno: (2017)
Vydáno: (2017)
Magnesia cement in the MgO-CO2-H2O system
Autor: Mitina N. A. Nataliya Aleksandrovna
Vydáno: (2022)
Autor: Mitina N. A. Nataliya Aleksandrovna
Vydáno: (2022)
Influence of Nitrogen on Corrosion Resistance of Thin Ti–O–N Films Deposited by Reactive Magnetron Sputtering
Autor: Boytsova E. L. Elena Lvovna
Vydáno: (2021)
Autor: Boytsova E. L. Elena Lvovna
Vydáno: (2021)
Investigation of laser heated spots on the surface of carbon steel
Autor: Lobankova O. V. Olga Vladimirovna
Vydáno: (2016)
Autor: Lobankova O. V. Olga Vladimirovna
Vydáno: (2016)
Metallurgy of a Ti–Au alloy synthesized by controlled electric resistance fusion
Vydáno: (2020)
Vydáno: (2020)
Podobné jednotky
-
Advances in small-scale resistance spot welding of the Ni-15 %Fe-4 %Mo-1 %Mn permalloy in the production of low-noise ring cores for fluxgate magnetometers
Vydáno: (2024) -
Optimization of Welding Parameters for Small-Scale Resistance Spot Welding of Zirconium Alloys
Autor: Slobodyan M. S. Mikhail Stepanovich
Vydáno: (2019) -
Evaluation of the reliability of resistance spot welding control via on-line monitoring of dynamic resistance
Vydáno: (2022) -
Effects of Electrode Degradation on Properties of Small-Scale Resistance Spot Welded Joints of E110 Alloy
Autor: Kiselev A. S. Aleksey Sergeevich
Vydáno: (2019) -
Prediction and stabilization of initial resistance between electrodes for small-scale resistance spot welding
Autor: Akbolatov E. Z. Eldos Zhannuruly
Vydáno: (2019)