Microstructure, microhardness and chemical composition of a detail obtained by electro-arc surfacing on a hardware-software complex of a delta layout; Structural Integrity and Life; Vol. 24, № 3

Microstructure, microhardness and chemical composition of a detail obtained by electro-arc surfacing on a hardware-software complex of a delta layout; Structural Integrity and Life; Vol. 24, № 3

Bibliographic Details
Parent link:	Structural Integrity and Life.— .— Belgrad: Society for Structural Integrity and Life Vol. 24, № 3.— 2024.— P. 351-359
Other Authors:	Kuznetsov M. A. Maksim Aleksandrovich, Proskokov A. V. Andrey Vladimirovich, Ilyashchenko D. P. Dmitry Pavlovich, Lavrova E. V. Elena Vladimirovna
Summary:	Title screen In the work, electric arc layer-by-layer surfacing of a lowcarbon low-alloyed wire in a carbon dioxide environment is carried out. The deposited metal structure in the form of a parallelepiped of thickness 4 mm and height 40 mm reveals the study of microstructure by optical microscopy, the composition of microhardness by indentation of drop tips and chemical composition by atomic emission spectral analysis. The obtained results show that products have a gradient structure. Only the last deposited zone has a dendritic structure. The underlying zones of secondary heat treatment, due to heat release from the upper layer, have a polyhedral recrystallized fine-grained ferritic-pearlitic structure. The microhardness of ejected deposited fibres changes from 1760 MPa to 1360 MPa in upper deposited layers. This is a general decrease in the pearlite fraction and the definition of ferrite. The evaluation of the chemical composition of deposited metal shows that in the first-fourth case, the metal of the deposited wire and substrate metal change, and the percentage of chemical elements in the thickness with the sixth composition of twenty approximately determines the metal of the deposited wire Текстовый файл
Language:	English
Published:	2024
Subjects:	electric arc surfacing with metal wire microstructure microhardness chemical composition электронный ресурс труды учёных ТПУ
Online Access:	https://doi.org/10.69644/ivk-2024-03-0351
Format:	Electronic Book Chapter
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=678033

Similar Items

Electron Beam Impact on Microstructure and Microhardness of Ti–6Al–4V Titanium Alloy Produced by Wire Electron-Beam Additive Manufacturing Technology and Selective Laser Alloying at Simulation of Electronic-Beam Welding; Physics of Metals and Metallography; Vol. 125, iss. 7
Published: (2024)

Microstructural Transformation and Enhanced Strength of Wire-Feed Electron-Beam Additive Manufactured Ti–6Al–4V Alloy Induced by High-Pressure Torsion; Advanced Engineering Materials; Vol. 26, iss. 4
Published: (2024)

Effect of Ultrasonic Impact Treatment on Microstructure and Fatigue Life of 3D Printed Ti–6Al–4V Titanium Alloy; Physics of Metals and Metallography; Vol. 124, iss. 10
Published: (2023)

Increasing the Fatigue Durability of an 3D-Printed Ti-6Al-4V Alloy Electron-Beam Welded Joint by Ultrasonic Electropulsing Shock Treatment; Physics of Metals and Metallography; Vol. 123, iss. 12
Published: (2022)

The Effect of Electropulsing-Assisted Ultrasonic Impact Treatment on the Microstructure, Phase Composition, and Microhardness of Electron-Beam-Welded 3D Printed Ti-6Al-4V Alloy; Physics of Metals and Metallography; Vol. 123, iss. 9
Published: (2022)

Influence of duty cycle in arc ion plating on the microstructure, electrochemical and high-temperature oxidation behavior of Cr coated Zr alloy; Surface and Coatings Technology; Vol. 517
Published: (2025)

Formation of Structural-Phase States in Alumina Ceramics VK-95 by Sintering in a Constant Magnetic Field; Russian Physics Journal; Vol. 62, iss. 2
Published: (2019)

Микроструктура и механические свойства спеченных образцов жаропрочной 12%-й хромистой ферритно-мартенситной стали; Перспективы развития фундаментальных наук; Т. 1 : Физика
by: Тимошов И. С.
Published: (2025)

The Effect of Electron Beam Welding on the Microstructure and Microhardness of 3D-Printed Products from Titanium Alloy Ti-6Al-4V; Physics of Metals and Metallography; Vol. 122, iss. 2
Published: (2021)

Микроструктура и микромеханизмы разрушения сплава системы Ni-Cr-Al, полученного методом электронно-лучевого аддитивного производства; Перспективы развития фундаментальных наук; Т. 1 : Физика
by: Лысунец М. А.
Published: (2025)

Comparative Analysis of Weld Microstructure in Ti-6Al-4V Samples Produced by Rolling and Wire-Feed Electron Beam Additive Manufacturing; Physical Mesomechanics; Vol. 26, iss. 6
Published: (2023)

Microstructure and Compressive Behavior of Ti-6Al-4V Alloy Built by Electron Beam Free-Form Fabrication; Journal of Materials Engineering and Performance; Vol. 29, iss. 11
Published: (2020)

Effect of Surface Electropulsing Assisted Ultrasonic Impact Treatment on the Microstructure, Phase Composition, and Microhardness of 3D Printed Ti-6Al-4V Alloy; Physics of Metals and Metallography; Vol. 122, iss. 7
by: Perevalova O. B. Olga Borisovna
Published: (2021)

Microstructure and scratch behavior of TiB/Ti-6Al-4V composites fabricated by wire-feed electron beam additive manufacturing; Materials Letters; Vol. 405
Published: (2026)

The Effect of Thermal Annealing on Mechanical and Optical Properties of MgAl2O4 Ceramics Fabricated by Spark Plasma Sintering; Russian Physics Journal; Vol. 67, No. 4
Published: (2024)

Microstructure and Phase Composition of 3D Printed Titanium Metal Matrix Composites Based on Ti-Al-V-Fe System and Reinforced with TiC Particles; Russian Physics Journal; Vol. 67, iss. 9
Published: (2024)

LiF influence on spark plasma sintering and structure of transparent MgAl2O4 ceramics; Russian Physics Journal; Vol. 68, iss. 4
Published: (2025)

The Influence of Dimesions and Phase State of Structural Elements on Mechanical Properties of Binary Alloys of the Ti–Nb and Zr–Nb Systems; Russian Physics Journal; Vol. 61, iss. 10
Published: (2019)

Beam Current Effect on Microstructure and Properties of Electron-Beam-Melted Ti-6Al-4V Alloy; Journal of Materials Engineering and Performance; Vol. 28, iss. 10
Published: (2019)

Zn- or Cu-containing CaP-based coatings formed by micro-arc oxidation on titanium and Ti-40Nb Alloy: Part I-Microstructure, composition and properties; Materials; Vol. 13, iss. 18
Published: (2020)

Effects of Water Cooling on the Microstructure of Electron Beam Additive-Manufactured Ti-6Al-4V; Metals; Vol. 11, iss. 11
Published: (2021)

Effect of Protective Coatings in Welded Constructions on Welding Stability and Electrode Metal Transfer into a Weld Pool in MMA; Solid State Phenomena; Vol. 303
Published: (2020)

Таблицы arc sin x arc tg x: пер. с англ.
Published: (Москва, Вычислительный центр АН СССР, 1960)

Transformations of the Microstructure and Phase Compositions of Titanium Alloys during Ultrasonic Impact Treatment Part III: Combination with Electrospark Alloying Applied to Additively Manufactured Ti-6Al-4V Titanium Alloy; Metals; Vol. 13, iss. 5
Published: (2023)

Stability of MMA welding with protective coatings; Structural Integrity and Life; Vol. 20, № 1
Published: (2020)

The Influence of Two-Jet Gas Shielding Parameters on the Structure and Microhardness of Steel 45 Joints during Consumable Electrode Welding; Metals; Vol. 13, iss. 6
by: Chinakhov D. A. Dmitriy Anatol'evich
Published: (2023)

Microhardness Homogeneity and Microstructure of High-Nitrogen Austenitic Steel Processed by High-Pressure Torsion; AIP Conference Proceedings; Vol. 1909 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2017 (AMHS’17)
Published: (2017)

The Formation of One-Piece Bimetallic Joint Made of X6CrNiTi18-10 Steel and 36CrNiTiAl Alloy; AIP Conference Proceedings; Vol. 1783 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2016
by: Svyazhina N. V.
Published: (2016)

Additive Manufacturing of Metal Products via Filler Wire Arc Welding (Review); Materials Science Forum; Vol. 1064
Published: (2022)

Quality of Metal Deposited Flux Cored Wire with the System Fe-C-Si-Mn-Cr-Mo-Ni-V-Co; Key Engineering Materials; Vol. 736 : Materials and their Application
Published: (2017)

Obtaining a Material Based on Я-SiC and Carbon Fibers Using an Electric Arc Technique; Inorganic Materials: Applied Research; Vol. 10, iss. 4
Published: (2019)

The structure - phase state and microhardness of the surface layer of the VT1-0 titanium alloys treated by copper ions; Vacuum; Vol. 149
Published: (2018)

Deformation Behavior of Wrought and EBAM Ti-6Al-4V under Scratch Testing; Metals; Vol. 11, iss. 11
Published: (2021)

Spatial stabilization of arc discharges in pulsed gas tungsten arc welding; Welding in the World; Vol. 68, iss. 9
Published: (2024)

The Effect of Heat Treatment on the Microstructure and Phase Composition of Wrought and 3D-Printed Ti–5Al–3Mo–1V Titanium Alloy Samples; Journal of Surface Investigation: X-ray, Synchrotron and Neutron Techniques; Vol. 17, Suppl. 1
Published: (2023)

Technological Improvement of Surfacing of Parts of Hammer Crushers Used in Coke-Chemical Industry; Materials Science Forum; Vol. 927 : Materials and Processing Technology II
Published: (2018)

Теория электрических цепей. Анализ ARC-цепи и расчет LC-фильтра методические указания к выполнению курсовой работы
by: Павлов В. Я.
Published: (Санкт-Петербург, СПбГУТ им. М.А. Бонч-Бруевича, 2013)

Initiation of an Arc Discharge in a Coaxial Magnetoplasma Accelerator; Russian Electrical Engineering; Vol. 89, iss. 3
by: Sivkov A. A. Aleksandr Anatolyevich
Published: (2018)

In-situ carbide reinforced aluminium metal matrix composites obtained in pulsed arc plasma discharge; Ceramics International; Vol. 51, iss. 14
Published: (2025)

Numerical Simulation of Thermal Processes in Welding with Pulsed Electrode Wire Feeding; Materials Science Forum; Vol. 927 : Materials and Processing Technology II
Published: (2018)