Effect of Ultrasonic Impact Treatment on Microstructure and Fatigue Life of 3D Printed Ti–6Al–4V Titanium Alloy

Effect of Ultrasonic Impact Treatment on Microstructure and Fatigue Life of 3D Printed Ti–6Al–4V Titanium Alloy

Dades bibliogràfiques
Parent link:	Physics of Metals and Metallography.— .— New York: Springer Science+Business Media LLC. Vol. 124, iss. 10.— 2023.— P. 1059-1065
Autor corporatiu:	Национальный исследовательский Томский политехнический университет
Altres autors:	Perevalova O. B. Olga Borisovna, Panin A. V. Alexey Viktorovich, Kazachenok M. S. Marina Sergeevna, Martynov S. A. Sergey Andreevich
Sumari:	Title screen Ultrasonic impact treatment (UIT) of Ti–6Al–4V alloy specimens, produced by wire-feed electron beam additive manufacturing technology, was carried out using a Co–WC hard alloy striker. Using the methods of X-ray diffraction analysis and transmission electron microscopy, it has been shown that UIT leads to the appearance of compressive macrostresses in the surface layers of the specimen, elastic microdeformations in the crystal lattice of the α-phase, formation of a gradient structure from nanocrystalline structure at a depth of up to 5 μm to submicrocrystalline structure of the α-phase at a depth of 15 to 40 μm. A nanocrystalline phase of titanium oxides is formed in the grains of the α-phase. The UIT results in an increase in microhardness and fatigue life. Fractographic analysis of specimen fractures after cyclic stretching in lowcycle fatigue mode has been carried out Текстовый файл
Publicat:	2023
Matèries:	электронный ресурс труды учёных ТПУ Ti-6Al-4V titanium alloy wire-feed electron beam additive manufacturing technology ultrasonic impact treatment X-ray analysis phase composition microstructure microhardness fatigue life fractographic analysis
Accés en línia:	https://doi.org/10.1134/S0031918X23601816
Format:	Electrònic Capítol de llibre
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=672029

Ítems similars

Increasing the Fatigue Durability of an 3D-Printed Ti-6Al-4V Alloy Electron-Beam Welded Joint by Ultrasonic Electropulsing Shock Treatment
Publicat: (2022)

Microstructural Transformation and Enhanced Strength of Wire-Feed Electron-Beam Additive Manufactured Ti–6Al–4V Alloy Induced by High-Pressure Torsion
Publicat: (2024)

Microstructure and Phase Composition of 3D Printed Titanium Metal Matrix Composites Based on Ti-Al-V-Fe System and Reinforced with TiC Particles
Publicat: (2024)

Transformations of the Microstructure and Phase Compositions of Titanium Alloys during Ultrasonic Impact Treatment Part III: Combination with Electrospark Alloying Applied to Additively Manufactured Ti-6Al-4V Titanium Alloy
Publicat: (2023)

Effect of Heat Input on the Microstructure and Phase Composition of Additively Manufactured Ti–6Al–4V Alloy
per: Kamelina K. D. Kristina Dmitrievna
Publicat: (2024)

The Effect of Heat Treatment on the Microstructure and Phase Composition of Wrought and 3D-Printed Ti–5Al–3Mo–1V Titanium Alloy Samples
Publicat: (2023)

Comparative Analysis of Weld Microstructure in Ti-6Al-4V Samples Produced by Rolling and Wire-Feed Electron Beam Additive Manufacturing
Publicat: (2023)

The Effect of Electropulsing-Assisted Ultrasonic Impact Treatment on the Microstructure, Phase Composition, and Microhardness of Electron-Beam-Welded 3D Printed Ti-6Al-4V Alloy
Publicat: (2022)

Deformation Behavior of Wrought and EBAM Ti-6Al-4V under Scratch Testing
Publicat: (2021)

Effect of Surface Electropulsing Assisted Ultrasonic Impact Treatment on the Microstructure, Phase Composition, and Microhardness of 3D Printed Ti-6Al-4V Alloy
per: Perevalova O. B. Olga Borisovna
Publicat: (2021)

Microstructure and Phase Composition of VT1-0, VT6, and VT14 Titanium Alloys Produced by Wire-Feed Electron-Beam Additive Manufacturing
Publicat: (2022)

Electron Beam Impact on Microstructure and Microhardness of Ti–6Al–4V Titanium Alloy Produced by Wire Electron-Beam Additive Manufacturing Technology and Selective Laser Alloying at Simulation of Electronic-Beam Welding
Publicat: (2024)

The Effect of Electron Beam Welding on the Microstructure and Microhardness of 3D-Printed Products from Titanium Alloy Ti-6Al-4V
Publicat: (2021)

Исследование структуры и свойств SLM-образцов ВТ6 обработанных комбинированным ультразвуковым и электрическим воздействием
per: Панин С. В. Сергей Викторович
Publicat: (2020)

Beam Current Effect on Microstructure and Properties of Electron-Beam-Melted Ti-6Al-4V Alloy
Publicat: (2019)

Рентгеноструктурные исследования аддитивно полученного образца титанового сплава Ti-6Al-4V при газофазном наводораживании
per: Камелина К. Д. Кристина Дмитриевна
Publicat: (2025)

In Situ High-Temperature Synchrotron X-ray Studies of Microstructure and Phase Composition of Additively Fabricated Ti–6Al–4V/TiC Metal Matrix Composite
Publicat: (2025)

Effects of Water Cooling on the Microstructure of Electron Beam Additive-Manufactured Ti-6Al-4V
Publicat: (2021)

Особенности формирования сварного шва в изделиях из титанового сплава Ti-6Al-4V, полученных аддитивными методами
per: Яхин А. Альберт
Publicat: (2020)

Hydrogen-Induced Phase Transformation and Microstructure Evolution for Ti-6Al-4V Parts Produced by Electron Beam Melting
Publicat: (2018)

Change in the Phase Composition and Lattice Parameters of the Solid Solution Based on a-Ti in the Surface Layers of the Ti–6Al–4V Alloy Subjected to Electron-Beam Treatment
per: Perevalova O. B. Olga Borisovna
Publicat: (2020)

In-situ X-ray diffraction study of hydrogen-induced phase transformation in wire-feed electron-beam additive manufactured Ti-6Al-4V alloy
Publicat: (2025)

Influence of manufacturing parameters on microstructure and hydrogen sorption behavior of electron beam melted titanium Ti-6Al-4V alloy
Publicat: (2018)

The impact of ultrasonic post-manufacturing on the microstructure of the metallic sheet-based triply periodic minimal surfaces manufactured by electron beam melting
per: Khrapov D. Dmitriy
Publicat: (2023)

Effect of Ultrasonic Impact Treatment on Structural Phase Transformations in Ti-6Al-4V Titanium Alloy
Publicat: (2022)

The Microstructural and Phase Evolution of the 3D Printed Ti-6Al-4V Alloy during Mechanical Loading
Publicat: (2023)

Transformations of the Microstructure and Phase Compositions of Titanium Alloys during Ultrasonic Impact Treatment. Part I. Commercially Pure Titanium
Publicat: (2021)

Applying Digital Image Correlation Technique for Studying the Growth of a Fatigue Crack in VT23 Titanium Alloy Welded Joints
Publicat: (2019)

The High-Temperature In Situ Synchrotron Study of the Structural-Phase Transformations in 3D-Printed Ti–6Al–4V and Ti–5Al–3Mo–V Titanium Alloys
Publicat: (2024)

Microstructure and Compressive Behavior of Ti-6Al-4V Alloy Built by Electron Beam Free-Form Fabrication
Publicat: (2020)

Scale levels of quasi-static and dynamic fracture behavior of Ti-6Al-4V parts built by various additive manufacturing methods
Publicat: (2020)

In situ study of phase transformations in electron beam additive manufactured Ti-6Al-4 V titanium alloy by high temperature synchrotron X-ray diffraction and TEM
per: Perevalova O. B. Olga Borisovna
Publicat: (2022)

Heparin Enriched-WPI Coating on Ti6Al4V Increases Hydrophilicity and Improves Proliferation and Differentiation of Human Bone Marrow Stromal Cells
Publicat: (2022)

Improving mechanical properties of wire-based EBAM Ti-6Al-4V parts by adding TiC powders
Publicat: (2021)

Functionalization of additive-manufactured Ti6Al4V scaffolds with poly(allylamine hydrochloride)/poly(styrene sulfonate) bilayer microcapsule system containing dexamethasone
Publicat: (2021)

Микроструктура и микромеханизмы разрушения сплава системы Ni-Cr-Al, полученного методом электронно-лучевого аддитивного производства
per: Лысунец М. А.
Publicat: (2025)

Fractography, Fracture Toughness and Structural Turbulence Under Low-Temperature Shock Loading of a Nonequilibrium Titanium Alloy Ti-6Al-4V
Publicat: (2020)

Modification of Ti-6Al-4V alloy element and phase composition by compression plasma flows impact
Publicat: (2018)

Influence of anisotropy properties and structural inhomogeneity on elasticity and fracture of titanium alloys produced by electron-beam melting
Publicat: (2025)

Microstructure, phase composition and hardness of Ti–Au cladding deposited on Ti–6Al–4V substrate by electron beam powder bed fusion method
Publicat: (2022)