Influence of Surface Sputtering during High-Intensity, Hot Ion Implantation on Deep Alloying of Martensitic Stainless Steel; Metals; Vol. 13 - iss. 9

Influence of Surface Sputtering during High-Intensity, Hot Ion Implantation on Deep Alloying of Martensitic Stainless Steel; Metals; Vol. 13 - iss. 9

Dettagli Bibliografici
Parent link:	Metals.— .— Basel: MDPI AG Vol. 13 - iss. 9.— 2023.— Article number 1604, 15 p.
Ente Autore:	National Research Tomsk Polytechnic University
Altri autori:	Ryabchikov A. I. Aleksandr Ilyich, Korneva O. S. Olga Sergeevna, Ivanova A. I. Anna Ivanovna, Dektyarev S. V. Sergey Valentinovich, Vakhrushev D. O. Dimitry Olegovich, Gurulev A. V. Aleksandr Valerjevich
Riassunto:	This article is devoted to the study of the effect of ion sputtering on the alloy surface, using the example of martensitic stainless steel AISI 420 with ultrahigh-dose, high-intensity nitrogen ion implantation on the efficiency of accumulation and transformation of the depth distribution of dopants. Some patterns of change in the depth of ion doping depending on the target temperature in the range from 400 to 650 ◦C, current density from 55 to 250 mA/cm2, and ion fluence up to 4.5 × 1021 ion/cm2 are studied. It has been experimentally established that a decrease in the ion sputtering coefficient of the surface due to a decrease in the energy of nitrogen ions from 1600 to 350 eV, while maintaining the ion current density, ion irradiation fluence and temperature mode of target irradiation increases the ion-doped layer depth by more than three times from 25 µm to 65 µm. The efficient diffusion coefficient at an ion doping depth of 65 µm is many times greater than the data obtained when stainless steel is nitrided with an ion flux with a current density of about 2 mA/cm2. Текстовый файл
Lingua:	inglese
Pubblicazione:	2023
Soggetti:	martensitic stainless steel ultrahigh-dose high-intensity ion implantation ion surface sputtering depth of ion doping труды учёных ТПУ электронный ресурс
Accesso online:	http://earchive.tpu.ru/handle/11683/132519 https://doi.org/10.3390/met13091604
Natura:	Elettronico Capitolo di libro
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=671733

Documenti analoghi

Modification of the microstructure and properties of martensitic steel during ultra-high dose high-intensity implantation of nitrogen ions; Surface and Coatings Technology; Vol. 388
Pubblicazione: (2020)

Investigation of the Features of High-Intensity Implantation of Nitrogen Ions into Titanium; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 17, s. 1
Pubblicazione: (2023)

Spectral analysis of nanosize forms of carbon synthesized by pulsed intense ion beams; Vacuum; Vol. 89
Pubblicazione: (2013)

Temperature Gradients in the Targets During High-Intensity Implantation in Forced Cooling; Energy Fluxes and Radiation Effects (EFRE-2020 online)
Pubblicazione: (2020)

Features of High-Intensity Implantation of Chromium into Zr1%Nb Alloy Using a High-Power Density Repetitively-Pulsed Ion Beam; Journal of Surface Investigation: X-ray, Synchrotron and Neutron Techniques; Vol. 19, iss. 4
Pubblicazione: (2025)

Investigation of High-Intensity Implantation of Titanium Ions into Silicon under Conditions of Beam Energy Impact on the Surface; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 18, iss. 5
Pubblicazione: (2024)

Low energy, high intensity metal ion implantation method for deep dopant containing layer formation; Surface and Coatings Technology; Vol. 355
Pubblicazione: (2018)

Temperature gradients in targets at low energy high-intensity ion implantation; Surface and Coatings Technology; Vol. 389
Pubblicazione: (2020)

DIN 1.7035 Steel Modification with High Intensity Nitrogen Ion Implantation; Russian Physics Journal; Vol. 61, iss. 2
Pubblicazione: (2018)

Effect of Preliminary Irradiation of 321 Steel Substrates with High-Intense Pulsed Ion Beams on Scratch Test Results of Subsequently Deposited AlN Coatings; Coatings; Vol. 11, iss. 10
Pubblicazione: (2021)

Ion Plasma Passivation of X10CrNiTi18-9 Stainless Steel Samples; AIP Conference Proceedings; Vol. 1783 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2016
Pubblicazione: (2016)

Progress in low energy high intensity ion implantation method development; Surface and Coatings Technology; Vol. 388
di: Ryabchikov A. I. Aleksandr Ilyich
Pubblicazione: (2020)

Study of craters formed on surface of AISI 321 stainless steel after high power ion-beam exposure; Vacuum; Vol. 198
Pubblicazione: (2022)

Numerical Simulation of Temperature Field Dynamics in Single-Crystal Silicon at Repetitively-Pulsed High-Intensity Ion Implantation and Energy Impact on the Surface Layer; Russian Physics Journal; Vol. 65, iss. 11
Pubblicazione: (2023)

Modification of silicon under synergy of high-intensity implantation of titanium ions and energy influence of a high-power ion beam on a surface; Materials. Technologies. Design; Т. 6, № 1
Pubblicazione: (2024)

High Intensity low Aluminum Ion Energy Implantation into Titanium; Ion Implantation Technology (IIT 2018)
Pubblicazione: (2018)

Numerical Simulation of Thermal Processes and the Effect of Heating of Near-Surface Layers of Titanium on the Diffusion Transfer of Dopants during High-Intensity Pulsed Ion Implantation; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 17, iss. 6
di: Ivanova A. I. Anna Ivanovna
Pubblicazione: (2023)

Numerical Modeling of Thermal Processes and the Effect of Heating of Near-Surface Silicon Layers on the Titanium Accumulation and Diffusion during High-Intensity Pulsed Ion Implantation; Journal of Surface Investigation: X-ray, Synchrotron and Neutron Techniques; Vol. 19, iss. 4
di: Ivanova A. I. Anna Ivanovna
Pubblicazione: (2025)

Investigation of Regularities of High-Intensity Ion Implantation in Combination with Subsequent Exposure to the Surface of a High-Current Electron Beam; Energy Fluxes and Radiation Effects (EFRE-2020 online)
Pubblicazione: (2020)

Modeling of Temperature Fields in Metals and Alloys under the Energy Impact of High-Pulse Power Ion Beams with Submillisecond Duration; Journal of Surface Investigation: X-ray, Synchrotron and Neutron Techniques; Vol. 19, iss. 4
di: Ryabchikov A. I. Aleksandr Ilyich
Pubblicazione: (2025)

Special Aspects of High-Intensity Low-Energy Ion Implantation; Russian Physics Journal; Vol. 63, iss. 10
Pubblicazione: (2021)

Repetitively-pulsed nitrogen implantation in titanium by a high-power density ion beam; Energy Fluxes and Radiation Effects (EFRE); International Conference on Modification of Materials with Particle Beams and Plasma Flows (16th CMM)
Pubblicazione: (2022)

Microstructure of titanium alloy modified by high-intensity implantation of low- and high-energy aluminium ions; Surface and Coatings Technology; Vol. 391
Pubblicazione: (2020)

Production of Workpieces from Martensitic Stainless Steel Using Electron-Beam Surfacing and Investigation of Cutting Forces When Milling Workpieces; Materials; Vol. 16, iss. 13
Pubblicazione: (2023)

High-Intensity Implantation With an Ion Beam's Energy Impact on Materials; IEEE Transactions on Plasma Science; Vol. 49, iss. 9
di: Ryabchikov A. I. Aleksandr Ilyich
Pubblicazione: (2021)

High-intensity chromium ion implantation into Zr-1Nb alloy; Surface and Coatings Technology; Vol. 383
Pubblicazione: (2020)

Features of thermal processes and the influence of pulsed heating of surface layers of titanium on the diffusion transfer of dopants during high-intensity ion implantation; Materials. Technologies. Design; Т. 5, № 3 (13)
di: Gurulev A. V. Aleksandr Valerjevich
Pubblicazione: (2023)

Surface modification of Al by high-intensity low-energy Ti-ion implantation: Microstructure, mechanical and tribological properties; Surface and Coatings Technology; Vol. 372
Pubblicazione: (2019)

Study of the synergy effect of high-intensity aluminum ions implantation into titanium and energy impact on the surface; Materials. Technologies. Design; Т. 5, № 3 (13)
Pubblicazione: (2023)

Ultra high fluence implantation of aluminum ions into CP–Ti; Journal of Alloys and Compounds; Vol. 793
Pubblicazione: (2019)

Electrical and Photoelectric Properties of Polycrystalline Silicon after High-Intensity Short-Pulse Ion Implantation; Russian Physics Journal; Vol. 56, iss. 6
di: Kabyshev A. V. Alexander Vasilievich
Pubblicazione: (2013)

Исследование упрочнения поверхности сталей при комбинированном ионном и лазерном воздействии; Известия Томского политехнического университета [Известия ТПУ]; Т. 324, № 2 : Математика и механика. Физика
Pubblicazione: (2014)

Effect on microstructure of Fe80B13Si7 metallic glass irradiated by high intensity pulsed ion beam and He ions; Surface and Coatings Technology; Vol. 449
Pubblicazione: (2022)

Study of the influence of a powerful pulsed ion beam on titanium deeply-doped with aluminum; Vacuum; Vol. 217
Pubblicazione: (2023)

Structural-phase State of Cold Deformed Stainless Steel after High Power Pulsed Ion Beam Processing; Energy Fluxes and Radiation Effects (EFRE-2020 online)
Pubblicazione: (2020)

Features of titanium ion beams formation taking into account ion-electron emission realizing the synergy of high-intensity ion implantation and pulsed energy impact on the surface; Materials. Technologies. Design; Т. 5, № 4 (14)
di: D. O. Dimitry Olegovich
Pubblicazione: (2023)

Plasma-immersion formation of high-intensity gaseous ion beams; Vacuum; Vol. 165
Pubblicazione: (2019)

High-power ion beam sources for industrial application; Surface and Coatings Technology; Vol. 96, iss. 1
Pubblicazione: (1997)

High-intensity ion beams with submillisecond duration for synergistic of ion implantation and energy impact on the surface; Energy Fluxes and Radiation Effects (EFRE); International Conference on Modification of Materials with Particle Beams and Plasma Flows (16th CMM)
Pubblicazione: (2022)

The influence of ion irradiation on the properties of ceramic silicon carbide; Energy Fluxes and Radiation Effects (EFRE-2016)
Pubblicazione: (2016)