Increasing the Fatigue Durability of an 3D-Printed Ti-6Al-4V Alloy Electron-Beam Welded Joint by Ultrasonic Electropulsing Shock Treatment; Physics of Metals and Metallography; Vol. 123, iss. 12

Increasing the Fatigue Durability of an 3D-Printed Ti-6Al-4V Alloy Electron-Beam Welded Joint by Ultrasonic Electropulsing Shock Treatment; Physics of Metals and Metallography; Vol. 123, iss. 12

Detalles Bibliográficos
Parent link:	Physics of Metals and Metallography Vol. 123, iss. 12.— 2022.— [P. 1201-1207]
Autor Corporativo:	Национальный исследовательский Томский политехнический университет Инженерная школа ядерных технологий Отделение экспериментальной физики
Otros Autores:	Perevalova O. B. Olga Borisovna, Panin A. V. Alexey Viktorovich, Boyangin E. N. Evgeny Nikolaevich, Kazachenok M. S. Marina Sergeevna
Sumario:	Title screen It has been shown by X-ray diffraction that the ultrasonic electropulsing shock treatment of specimens with a Ti-6Al-4V alloy weld joint formed by the electron-beam wire additive technology with the use of a hard-alloy (Co-WC) striker leads to an increase in the volumetric content of the β-phase, the formation of Ti-Co and Ti-Co-Al intermetallide phases, an increase in the microhardness, and a 1.5-fold increase in fatigue durability compared to the initial state. After treatment, elastic compression macrostresses appear in the surface specimen layers to become higher in the basic material zone compared to the joint area. An increase in the fatigue durability of specimens with a weld joint after treatment is caused by the essential reinforcement of their surface layers due to the formation of intermetallide phases. The destruction of a specimen with a weld joint occurs after treatment in the joint area. Fracturing has been characterized as brittle in the surface layers of a specimen and as a predominantly viscous dimple far from its surface. Режим доступа: по договору с организацией-держателем ресурса
Lenguaje:	inglés
Publicado:	2022
Materias:	электронный ресурс труды учёных ТПУ titanium alloy electron-beam wire additive technology ultrasonic electropulsing shock treatment X-ray diffraction analysis phase composition microstructure microhardness fatigue durability
Acceso en línea:	https://doi.org/10.1134/S0031918X22601512
Formato:	Electrónico Capítulo de libro
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=669561

Ejemplares similares

Effect of Ultrasonic Impact Treatment on Microstructure and Fatigue Life of 3D Printed Ti–6Al–4V Titanium Alloy; Physics of Metals and Metallography; Vol. 124, iss. 10
Publicado: (2023)

The Effect of Electropulsing-Assisted Ultrasonic Impact Treatment on the Microstructure, Phase Composition, and Microhardness of Electron-Beam-Welded 3D Printed Ti-6Al-4V Alloy; Physics of Metals and Metallography; Vol. 123, iss. 9
Publicado: (2022)

Effect of Surface Electropulsing Assisted Ultrasonic Impact Treatment on the Microstructure, Phase Composition, and Microhardness of 3D Printed Ti-6Al-4V Alloy; Physics of Metals and Metallography; Vol. 122, iss. 7
por: Perevalova O. B. Olga Borisovna
Publicado: (2021)

Influence of long-term operation on structure, fatigue durability and impact toughness of 09Mn2Si pipe steel; Procedia Structural Integrity; Vol. 5 : 2nd International Conference on Structural Integrity, ICSI 2017, 4-7 September 2017, Funchal, Madeira, Portugal
Publicado: (2017)

The Effect of Advanced Ultrasonic Forging on Fatigue Fracture Mechanisms of Welded Ti-6А1-4V Alloy; AIP Conference Proceedings; Vol. 1909 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2017 (AMHS’17)
Publicado: (2017)

Определение напряжений и остаточного ресурса по показаниям датчика деформаций интегрального типа переменной чувствительности; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 328, № 9
por: Сызранцев В. Н. Владимир Николаевич
Publicado: (2017)

Microstructure, microhardness and chemical composition of a detail obtained by electro-arc surfacing on a hardware-software complex of a delta layout; Structural Integrity and Life; Vol. 24, № 3
Publicado: (2024)

Effect of Energy Deposition on High-Voltage Electropulse Drilling Efficiency in Granite; Journal of Mining Science; Vol. 53, iss. 3
Publicado: (2017)

Electron Beam Impact on Microstructure and Microhardness of Ti–6Al–4V Titanium Alloy Produced by Wire Electron-Beam Additive Manufacturing Technology and Selective Laser Alloying at Simulation of Electronic-Beam Welding; Physics of Metals and Metallography; Vol. 125, iss. 7
Publicado: (2024)

Influence of long-term cold climate operation on structure, fatigue durability and impact toughness of 09Mn2Si pipe steel; Engineering Failure Analysis; Vol. 102
Publicado: (2019)

Mechanical and durability aspects of concrete incorporating secondary aluminium slag; Resource-Efficient Technologies; Vol. 2, Iss. 4
por: Satish Reddy M.
Publicado: (2016)

Strengthening elements to increase fatigue strength of mine hoisting machine steel structures; Metalurgija; Vol. 61, No. 1
Publicado: (2022)

Transformations of the Microstructure and Phase Compositions of Titanium Alloys during Ultrasonic Impact Treatment Part III: Combination with Electrospark Alloying Applied to Additively Manufactured Ti-6Al-4V Titanium Alloy; Metals; Vol. 13, iss. 5
Publicado: (2023)

Low Cost Embedded Copper Mesh Based on Cracked Template for Highly Durability Transparent EMI Shielding Films; Materials; Vol. 15, iss. 4
Publicado: (2022)

Application of Phase-Reversal Fresnel Zone Plates for High-Resolution Robotic Ultrasonic Non-Destructive Evaluation; Sensors; Vol. 21, iss. 23
Publicado: (2021)

Microstructural Transformation and Enhanced Strength of Wire-Feed Electron-Beam Additive Manufactured Ti–6Al–4V Alloy Induced by High-Pressure Torsion; Advanced Engineering Materials; Vol. 26, iss. 4
Publicado: (2024)

Applying the Algorithm of Calculation in the Frequency Domain to Ultrasonic Tomography; Russian Journal of Nondestructive Testing; Vol. 54, iss. 4
Publicado: (2018)

Принципы анализа и типология в методологии экономических шоков; Векторы благополучия: экономика и социум; Т. 48, № 1
por: Жиронкин С. А. Сергей Александрович
Publicado: (2023)

Influence of the Cobalt Additive on the Flux Cored Wire of System Fe-C-Si-Mn-Cr-Ni-Mo-V; Key Engineering Materials; Vol. 736 : Materials and their Application
Publicado: (2017)

Algorithm of fatigue crack detection and determination of its tip position in optical images; Optoelectronics, Instrumentation and Data Processing; Vol. 53, iss. 3
Publicado: (2017)

Estimating Low- and High-Cyclic Fatigue of Polyimide-CF-PTFE Composite through Variation of Mechanical Hysteresis Loops; Materials; Vol. 15, iss. 13
Publicado: (2022)

An Automated Optical Strain Measurement System for Estimating Polymer Degradation under Fatigue Testing; Sensors; Vol. 22, iss. 16
Publicado: (2022)

Applying Digital Image Correlation Technique for Studying the Growth of a Fatigue Crack in VT23 Titanium Alloy Welded Joints; Russian Journal of Nondestructive Testing; Vol. 55, iss. 5
Publicado: (2019)

Comparative study of active infrared thermography, ultrasonic laser vibrometry and laser ultrasonics in application to the inspection of graphite/epoxy composite parts; Quantitative InfraRed Thermography Journal; Vol. XX
Publicado: (2019)

The breakup of gas bubbles by a shock wave: brief historical background; European Physical Journal H; Vol. 49
por: Minin I. V. Igor Vladilenovich
Publicado: (2024)

The effect of crater creation on the fatigue strength and corrosion resistance of steels and titanium alloys irradiated by high-power pulsed ion beams; Surface and Coatings Technology; Vol. 158-159
por: Shulov V. A.
Publicado: (2002)

Use of reinforcing elements to improve fatigue strength of steel structures of mine hoisting machines (MHM); Metalurgija; Vol. 59, № 1
Publicado: (2020)

Method for calculating the point spread function for the ultrasonic imaging of multi-layered objects with total focusing method; Russian Physics Journal; Vol. 68, iss. 3
por: Dolmatov D. O. Dmitry Olegovich
Publicado: (2025)

Application of ultrasonic shock surface treatment to increase fatigue strength of structural steel weldments; Korus 2004; Vol. 3
Publicado: (2004)

The Influence of Two-Jet Gas Shielding Parameters on the Structure and Microhardness of Steel 45 Joints during Consumable Electrode Welding; Metals; Vol. 13, iss. 6
por: Chinakhov D. A. Dmitriy Anatol'evich
Publicado: (2023)

Comparative study of shock-wave hardening and substructure evolution of 304L and Hadfield steels irradiated with a nanosecond relativistic high-current electron beam; Journal of Alloys and Compounds; Vol. 714
Publicado: (2017)

The Effect of Electron Beam Welding on the Microstructure and Microhardness of 3D-Printed Products from Titanium Alloy Ti-6Al-4V; Physics of Metals and Metallography; Vol. 122, iss. 2
Publicado: (2021)

Application of Fourier-Domain Post-Processing Technique for Ultrasonic Imaging with Matrix Phased Arrays in Advanced Manufacturing of Details and Machines; Materials Science Forum; Vol. 938 : Materials and Technologies in Mechanical Engineering
Publicado: (2018)

The Frequency-Domain Algorithm for Ultrasonic Imaging of Complex-Shaped Objects; Key Engineering Materials; Vol. 769 : High Technology: Research and Applications (HTRA 2017)
por: Dolmatov D. O. Dmitry Olegovich
Publicado: (2018)

Combined action of crack closure and residual stress under periodic overloads: A fractographic analysis; International Journal of Fatigue; Vol. 82, pt. 3
Publicado: (2016)

Влияние измельчения бакчарской железной руды на свойства воздушно-сухих и восстановленных торфорудных материалов; Известия Томского политехнического университета [Известия ТПУ]; Т. 325, № 3 : Химия и химические технологии
por: Архипов В. С. Виктор Сергеевич
Publicado: (2014)

Application of Phase-Reversal Fresnel Zone Plates for Improving The Elevation Resolution in Ultrasonic Testing with Phased Arrays; Sensors; Vol. 19, iss. 23
Publicado: (2019)

Applying the Algorithm of Calculation in the Frequency Domain to Ultrasonic Tomography of Layered Inhomogeneous Media Using Matrix Antenna Arrays; Russian Journal of Nondestructive Testing; Vol. 55, iss. 7
Publicado: (2019)

Сonsolidation of bimetallic nanosized particles and formation of nanocomposites depending on conditions of shock wave compaction; Russian Physics Journal; Vol. 60, No. 7
Publicado: (2017)

Optimal Design of Sparse Matrix Phased Array Using Simulated Annealing for Volumetric Ultrasonic Imaging with Total Focusing Method; Sensors; Vol. 24, iss. 6
por: Dolmatov D. O. Dmitry Olegovich
Publicado: (2024)