$In situ study of phase transformations in electron beam additive manufactured Ti-6Al-4 V titanium alloy by high temperature synchrotron X-ray diffraction and TEM; Journal of Alloys and Compounds; Vol. 917$

In situ study of phase transformations in electron beam additive manufactured Ti-6Al-4 V titanium alloy by high temperature synchrotron X-ray diffraction and TEM; Journal of Alloys and Compounds; Vol. 917

Dades bibliogràfiques
Parent link:	Journal of Alloys and Compounds Vol. 917.— 2022.— [165463, 11 p.]
Autor principal:	Perevalova O. B. Olga Borisovna
Autor corporatiu:	Национальный исследовательский Томский политехнический университет Инженерная школа ядерных технологий Отделение экспериментальной физики
Altres autors:	Syrtanov M. S. Maksim Sergeevich
Sumari:	Title screen The microstructure and phase composition of the EBAM Ti-6Al-4 V alloy samples were studied by the methods of in situ high temperature synchrotron X-ray diffraction and transmission electron microscopy (TEM) during heating from room temperature to a temperature of 1373 K. In the initial state, the main phase of the EBAM Ti-6Al-4 V alloy the samples was the α phase, the second phases were β + α″. The volume fraction of the β phase does not exceed 5%, α″ - 3%. It was found that the new α″ phase was formed at the temperature of 1073 K due to the phase transition α→α″. The α″ phase volume fraction increased as the heating temperature increased to the temperature of 1223 K and then decreased with a further increase of the temperature due to the α″→β phase transition. The dependences of the lattice parameters of the α, β and α″ phases on the heating temperature were revealed. It was established that the crystal lattice of the α phase was distorted during heating. The α phase passed into the unstable state. An increase of the c/a parameters ratio was accompanied by the formation of the α″ and β phases. Режим доступа: по договору с организацией-держателем ресурса
Idioma:	anglès
Publicat:	2022
Matèries:	электронный ресурс труды учёных ТПУ electron beam additive manufacturing Ti-6Al-4 V phase composition microstructure phase transformation α→α″ электронно-лучевое аддитивное производство фазовый состав микроструктуры фазовые превращения
Accés en línia:	https://doi.org/10.1016/j.jallcom.2022.165463
Format:	MixedMaterials Electrònic Capítol de llibre
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=668430

Ítems similars

In Situ Synchrotron Study of the Phase Transformations in Ti-5.7Al-1.6V-3Mo Titanium Alloy at High Temperature; Journal of Materials Engineering and Performance; Vol. 33, iss. 19
per: Perevalova O. B. Olga Borisovna
Publicat: (2024)

Electron Beam Impact on Microstructure and Microhardness of Ti–6Al–4V Titanium Alloy Produced by Wire Electron-Beam Additive Manufacturing Technology and Selective Laser Alloying at Simulation of Electronic-Beam Welding; Physics of Metals and Metallography; Vol. 125, iss. 7
Publicat: (2024)

In Situ High-Temperature Synchrotron X-ray Studies of Microstructure and Phase Composition of Additively Fabricated Ti–6Al–4V/TiC Metal Matrix Composite; Journal of Surface Investigation: X-ray, Synchrotron and Neutron Techniques; Vol. 19, iss. 4
Publicat: (2025)

Deformation Behavior of Wrought and EBAM Ti-6Al-4V under Scratch Testing; Metals; Vol. 11, iss. 11
Publicat: (2021)

Microstructure and Phase Composition of 3D Printed Titanium Metal Matrix Composites Based on Ti-Al-V-Fe System and Reinforced with TiC Particles; Russian Physics Journal; Vol. 67, iss. 9
Publicat: (2024)

Effect of Ultrasonic Impact Treatment on Microstructure and Fatigue Life of 3D Printed Ti–6Al–4V Titanium Alloy; Physics of Metals and Metallography; Vol. 124, iss. 10
Publicat: (2023)

From raw elements to 3D samples: An economical route for Co-Cr-Mo alloy fabrication; Journal of Alloys and Compounds; Vol. 978
Publicat: (2024)

Microstructure and Phase Composition of VT1-0, VT6, and VT14 Titanium Alloys Produced by Wire-Feed Electron-Beam Additive Manufacturing; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 16, iss. 6
Publicat: (2022)

Transformations of the Microstructure and Phase Compositions of Titanium Alloys during Ultrasonic Impact Treatment Part III: Combination with Electrospark Alloying Applied to Additively Manufactured Ti-6Al-4V Titanium Alloy; Metals; Vol. 13, iss. 5
Publicat: (2023)

Hydrogen-Induced Phase Transformation and Microstructure Evolution for Ti-6Al-4V Parts Produced by Electron Beam Melting; Metals; Vol. 8, iss. 5
Publicat: (2018)

The High-Temperature In Situ Synchrotron Study of the Structural-Phase Transformations in 3D-Printed Ti–6Al–4V and Ti–5Al–3Mo–V Titanium Alloys; Physics of Metals and Metallography; Vol. 125, iss. 9
Publicat: (2024)

The Effect of Heat Treatment on the Microstructure and Phase Composition of Wrought and 3D-Printed Ti–5Al–3Mo–1V Titanium Alloy Samples; Journal of Surface Investigation: X-ray, Synchrotron and Neutron Techniques; Vol. 17, Suppl. 1
Publicat: (2023)

Effect of Heat Input on the Microstructure and Phase Composition of Additively Manufactured Ti–6Al–4V Alloy; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 18, iss. 6
per: Kamelina K. D. Kristina Dmitrievna
Publicat: (2024)

In-situ X-ray diffraction study of hydrogen-induced phase transformation in wire-feed electron-beam additive manufactured Ti-6Al-4V alloy; Journal of Alloys and Compounds; Vol. 1045
Publicat: (2025)

Effects of Water Cooling on the Microstructure of Electron Beam Additive-Manufactured Ti-6Al-4V; Metals; Vol. 11, iss. 11
Publicat: (2021)

The Microstructural and Phase Evolution of the 3D Printed Ti-6Al-4V Alloy during Mechanical Loading; Physics of Metals and Metallography; Vol. 124, iss. 2
Publicat: (2023)

Microstructure and scratch behavior of TiB/Ti-6Al-4V composites fabricated by wire-feed electron beam additive manufacturing; Materials Letters; Vol. 405
Publicat: (2026)

Recovery of Scratch Grooves in Ti-6Al-4V Alloy Caused by Reversible Phase Transformations; Metals; Vol. 10, iss. 10
Publicat: (2020)

Microstructural Transformation and Enhanced Strength of Wire-Feed Electron-Beam Additive Manufactured Ti–6Al–4V Alloy Induced by High-Pressure Torsion; Advanced Engineering Materials; Vol. 26, iss. 4
Publicat: (2024)

Beam Current Effect on Microstructure and Properties of Electron-Beam-Melted Ti-6Al-4V Alloy; Journal of Materials Engineering and Performance; Vol. 28, iss. 10
Publicat: (2019)

Comparative Analysis of Weld Microstructure in Ti-6Al-4V Samples Produced by Rolling and Wire-Feed Electron Beam Additive Manufacturing; Physical Mesomechanics; Vol. 26, iss. 6
Publicat: (2023)

Change in the Phase Composition and Lattice Parameters of the Solid Solution Based on a-Ti in the Surface Layers of the Ti–6Al–4V Alloy Subjected to Electron-Beam Treatment; Physics of Metals and Metallography; Vol. 121, iss. 2
per: Perevalova O. B. Olga Borisovna
Publicat: (2020)

Spark Plasma Sintering of Paper-Derived Ti3AlC2-Based Composites: Influence of Sintering Temperature; Materials Science Forum; Vol. 1016 : THERMEC’2020/2021
Publicat: (2021)

Synthesis of MAX-Phase Ti3SiC2 by Combined Powder Metallurgy Technique; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 18, iss. 6
Publicat: (2024)

Ti3SiC2 MAX-Phase-Based Composites Produced by Vacuum and Spark Plasma Sintering; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 19, iss. 5
Publicat: (2025)

Исследование морфологии и фазового состава порошков алюминия, кремния и магния; Инновационные технологии в машиностроении
per: Сапрыкина Н. А. Наталья Анатольевна
Publicat: (2023)

Influence of manufacturing parameters on microstructure and hydrogen sorption behavior of electron beam melted titanium Ti-6Al-4V alloy; Materials; Vol. 11, iss. 5
Publicat: (2018)

Heparin Enriched-WPI Coating on Ti6Al4V Increases Hydrophilicity and Improves Proliferation and Differentiation of Human Bone Marrow Stromal Cells; International Journal of Molecular Sciences; Vol. 23, iss. 10
Publicat: (2022)

Deformation and Fracture of Ti-6Al-4V/TiC Composites 3D Printed using Wire-Feed Electron Beam Additive Manufacturing under Uniaxial Tensile Stress; Physical Mesomechanics; Vol. 28, iss. 6
Publicat: (2025)

Surface Modification of the EBM Ti-6Al-4V Alloy by Pulsed Ion Beam; Metals; Vol. 11, iss. 3
Publicat: (2021)

Functionalization of additive-manufactured Ti6Al4V scaffolds with poly(allylamine hydrochloride)/poly(styrene sulfonate) bilayer microcapsule system containing dexamethasone; Materials Chemistry and Physics; Vol. 273
Publicat: (2021)

Improving mechanical properties of wire-based EBAM Ti-6Al-4V parts by adding TiC powders; Material Design and Processing Communications (MDPS); Vol. 3, iss. 1
Publicat: (2021)

The Effect of Nanoscale Mesoscopic Structural States Associated with Lattice Curvature on the Mechanical Behavior of Ti–6Al–4V Alloy; Physical Mesomechanics; Vol. 23, iss. 6
Publicat: (2020)

Селективное лазерное плавление магния; Инновационные технологии в машиностроении
per: Сапрыкина Н. А. Наталья Анатольевна
Publicat: (2019)

Comparison the Preparation Methods of Powder Feedstock for Laser Powder Bed Fusion; Solid State Phenomena; Vol. 328
Publicat: (2022)

Modification of Ti-6Al-4V alloy element and phase composition by compression plasma flows impact; Surface and Coatings Technology; Vol. 355
Publicat: (2018)

Increasing the Fatigue Durability of an 3D-Printed Ti-6Al-4V Alloy Electron-Beam Welded Joint by Ultrasonic Electropulsing Shock Treatment; Physics of Metals and Metallography; Vol. 123, iss. 12
Publicat: (2022)

Effect of the Beam Current during the Electron-Beam Melting of Titanium Alloy Ti-6Al-4V on the Structural Features and Phase Transitions in Gas-Phase Hydrogenation; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 13, No. 3
Publicat: (2019)

Effect of Surface Electropulsing Assisted Ultrasonic Impact Treatment on the Microstructure, Phase Composition, and Microhardness of 3D Printed Ti-6Al-4V Alloy; Physics of Metals and Metallography; Vol. 122, iss. 7
per: Perevalova O. B. Olga Borisovna
Publicat: (2021)

Assessment of Microstructural, Mechanical and Electrochemical Properties of Ti–42Nb Alloy Manufactured by Electron Beam Melting; Materials; Vol. 16, iss. 13
Publicat: (2023)