DIC Study of Fatigue Crack Growth after Single Overloads and Underloads

DIC Study of Fatigue Crack Growth after Single Overloads and Underloads

Bibliografski detalji
Parent link:	Procedia Structural Integrity Vol. 5 : 2nd International Conference on Structural Integrity, ICSI 2017, 4-7 September 2017, Funchal, Madeira, Portugal.— 2017.— [P. 889-895]
Autor kompanije:	Национальный исследовательский Томский политехнический университет Инженерная школа новых производственных технологий Отделение материаловедения
Daljnji autori:	Eremin A. V. Alexandr Vyacheslavovich, Panin S. V. Sergey Viktorovich, Ramasubbu S. Sunder, Berto F. Filippo
Sažetak:	Title screen The paper describes near-tip experimental strain measurements under simple variable-amplitude loading. Local strain was estimated by means of Digital Image Correlation (DIC) technique using optical microscope equipped with digital camera. Fatigue crack growth tests were performed on single edge crack tension specimens made of Al-Cu alloy under specially designed load sequences, which included baseline cycles, single overload or underload with measurement cycles for DIC. The main idea of the study is to compare strain response and shapes of hysteresis loops at the crack tip and crack wake. The obtained results suggest that COD values measured at the crack tip are significantly affected by both underload and overload, but the influence is different for each case. The observed behavior is attributed to abrupt changes in Kop and ΔKth and their subsequent recovery to the basic level. Режим доступа: по договору с организацией-держателем ресурса
Izdano:	2017
Teme:	электронный ресурс труды учёных ТПУ crack closure crack-tip blunting/re-sharpening variable-amplitude loading underload overload трещины нагрузки перегрузки
Online pristup:	https://doi.org/10.1016/j.prostr.2017.07.120
Format:	Elektronički Poglavlje knjige
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=667018

Slični predmeti

Synergy of crack closure, near-tip residual stress and crack-tip blunting in crack growth under periodic overloads – A fractographic study
Izdano: (2016)

Combined action of crack closure and residual stress under periodic overloads: A fractographic analysis
Izdano: (2016)

Synthesis of an automated control system for the flow of active power along a power line in overload condition
od: Postoyankova K. Yu.
Izdano: (2021)

Fracture resistance of the deposited metal under dynamic and cyclic loading
Izdano: (2024)

Resistance of Heterogeneous Metal Compositions to Fracture under Dynamic and Cyclic Loads
Izdano: (2023)

Technique of definition of cracking resistance characteristics of metal plates and envelopes of small thickness
od: Solyanik A. S.
Izdano: (2006)

Algorithm of fatigue crack detection and determination of its tip position in optical images
Izdano: (2017)

Движение волны фильтрации вдоль несвязной поверхности пористого тела
od: Таирова А. А. Алия Алиевна
Izdano: (2023)

Integrated mathematical modeling of catalytic cracking and zeolite-containing catalyst oxidative regeneration
Izdano: (2020)

Physico-Mathematical Modeling and Experimental Study of Cracks in Concrete Obtained by Exposure to a Pulsed High Voltage Discharge
Izdano: (2020)

Эмпирический метод распознавания группы стресс-коррозионных трещин в металле по сигналу накладного вихретокового преобразователя
od: Загидулин Р. В. Ринат Васикович
Izdano: (2022)

Cracking of Heavy Hydrocarbon Feedstocks in the Presence of Cobalt
Izdano: (2018)

Acoustic emission study on the effect of notch shape and temperature on elastic energy release during impact testing of 17Mn1Si pipe steel
Izdano: (2019)

Composition of Initiated Cracking Products of High-sulfur Natural Bitumen
Izdano: (2014)

Research of crack initiation and propagation under loading for providing impact resilience of protective coating
Izdano: (2019)

Crack healing of ferrosilicochromium-filled polymer-derived ceramiccomposites
Izdano: (2018)

New characterization models for macroscopic chemical-hydrodynamic behavior of catalytic cracking riser-reactor with interactive patterns of severe operating conditions using CFD calculations
od: Foroutan G. S. Ghazvini Saba
Izdano: (2024)

The quantity and amorphicity determination of oxidable coke on the zeolite-containing catalysts of cracking
Izdano: (2019)

Modeling of the catalytic cracking: Catalyst deactivation by coke and heavy metals
Izdano: (2020)

Increasing the economic efficiency of gasoline production: Reducing the quality giveaway and simulation of catalytic cracking and compounding
Izdano: (2019)

Coniferous Tree Ignition by Cloud-to-Ground Lightning Discharge Using Approximation of "Ideal" Crack in Bark
od: Baranovskiy N. V. Nikolay Viktorovich
Izdano: (2016)

Estimation of A516-70 Carbon Steel Fatigue Damage on the Basis of Acoustic Nonlinearity
Izdano: (2017)

Prediction of the light product yield from the catalytic cracking unit using the mathematical model
Izdano: (2016)

Strengthening elements to increase fatigue strength of mine hoisting machine steel structures
Izdano: (2022)

Study of crack resistance of TiAlN coatings by scratch testing
Izdano: (2017)

A predictive model of catalytic cracking: Feedstock-induced changes in gasoline and gas composition
Izdano: (2021)

Low Cost Embedded Copper Mesh Based on Cracked Template for Highly Durability Transparent EMI Shielding Films
Izdano: (2022)

Fluoride Processing of a Fluid Cracking Catalyst Resulting in the Recovery of a Rare-Earth-Element Concentrate
Izdano: (2021)

The forecasting of the catalytic cracking products yield depending on the feedstock composition and the catalyst activity
Izdano: (2019)

Инициированный крекинг природного битума для увеличения выхода дистиллятных фракций
od: Кривцов Е. Б. Евгений Борисович
Izdano: (2013)

Multiscale Fracture of Ti-Al-N Coatings under Uniaxial Tension
Izdano: (2021)

The Increase in the Yield of Light Fractions During the Catalytic Cracking of C13-C40 Hydrocarbons
Izdano: (2017)

Studies of kinetic plasticity effect in high-speed steels under Martensite transformation
od: Demenkova L. G. Larisa Gennadievna
Izdano: (2020)

Improvement of Thermal Cycling Resistance of AlxSi1−xN Coatings on Cu Substrates by Optimizing Al/Si Ratio
Izdano: (2019)

Reducing Oscillations in Suspension of Mine Monorail Track
Izdano: (2023)

Development of a Two-Fluid Hydrodynamic Model for a Riser Reactor
Izdano: (2022)

Influence of Feedstock Group Composition on the Octane Number and Composition of the Gasoline Fraction of Catalytically Cracked Vacuum Distillate
Izdano: (2018)

Структурные аспекты циклической прочности сварного узла пароперегревателя
Izdano: (2018)

Approaches to Description of the Composition and Properties of Vacuum Gas Oil for Constructing Mathematical Models of Deep Oil-Refining Processes
Izdano: (2024)

Structure and properties of welding joints of 1370 aluminum alloy obtained by electron-beam welding
od: Solov’ev V. V. Vasily Vladimirovich
Izdano: (2025)