The development of baking technology for bulk materials based on the use of alternative electric furnace
| Parent link: | Вестник Карагандинского университета. Серия Физика № 2 (98).— 2020.— [С. 93-100] |
|---|---|
| Συλλογικό Έργο: | , |
| Άλλοι συγγραφείς: | , , , |
| Περίληψη: | The article based on the experimental data and it describes the development of a rational design of an oscillatory system for controlled vibrational feeding of bulk materials during their heat treatment in furnaces with a vibratory base plate, which, together with the moving trolley on elastic connections, is the basis to transfer bulk material in the thermal field of an electric heating system with set processing time. To create nonsymmetric oscillations and to obtain unidirectional material motion at the horizontal furnace position, the conical springs are used. They should provide a gently inclined resonant peak, which can significantly reduce the sensitivity of the oscillating system to fluctuations of the natural frequency and excitation frequency, stiffness, friction and other factors under high temperatures and instability of the electrical network. However, the total elastic characteristic of the oscillatory system which is obtained as a result of the experiments consists of conical and cylindrical springs and shows a weakly expressed nonlinearity. Therefore, to achieve a transport effect it will require the installation of the entire furnace unit at an angle to the horizon. According to the available experimental data, a linear model of the oscillatory system was utilized. В статье на основе экспериментальных данных описана разработка рациональной конструкции колебательной системы для регулируемой вибрационной подачи сыпучих материалов при их термообработке в печах с вибрационной опорной плитой, которая вместе с подвижной тележкой на упругих связях является основой для переноса сыпучих материалов в тепловом поле электронагревательной системы с заданным временем обработки. Для создания несимметричных колебаний и получения однонаправленного движения материала в горизонтальном положении печи используются конические пружины. Они должны обеспечивать пологий наклон резонансного пика, что позволяет значительно снизить чувствительность колебательной системы к колебаниям собственной частоты и частоты возбуждения, жесткости, трению и другим факторам при высоких температурах и нестабильности электрической сети. Однако общая упругая характеристика колебательной системы, полученная в результате экспериментов, состоит из конических и цилиндрических пружин и демонстрирует слабо выраженную нелинейность. Поэтому для достижения транспортного эффекта потребуется установка всего печного агрегата под углом к горизонту. По имеющимся экспериментальным данным, была использована линейная модель колебательной системы. |
| Γλώσσα: | Αγγλικά |
| Έκδοση: |
2020
|
| Θέματα: | |
| Διαθέσιμο Online: | http://earchive.tpu.ru/handle/11683/80973 https://doi.org/10.31489/2020Ph2/93-100 |
| Μορφή: | Ηλεκτρονική πηγή Κεφάλαιο βιβλίου |
| KOHA link: | https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=665265 |
MARC
| LEADER | 00000naa0a2200000 4500 | ||
|---|---|---|---|
| 001 | 665265 | ||
| 005 | 20241105134057.0 | ||
| 035 | |a (RuTPU)RU\TPU\network\36464 | ||
| 035 | |a RU\TPU\network\36325 | ||
| 090 | |a 665265 | ||
| 100 | |a 20210907a2020 k y0engy50 ba | ||
| 101 | 0 | |a eng | |
| 102 | |a KZ | ||
| 135 | |a drcn ---uucaa | ||
| 181 | 0 | |a i |b e | |
| 182 | 0 | |a b | |
| 183 | 0 | |a cr |2 RDAcarrier | |
| 200 | 1 | |a The development of baking technology for bulk materials based on the use of alternative electric furnace |d Разработка технологии обжига сыпучих материалов на основе использования альтернативной электропечи |f A. I. Nizhegorodov, A. N. Gavrilin, B. B. Moyzes [Moises], K. A. Kuvshinov | |
| 203 | |a Text |c electronic | ||
| 320 | |a [Библиогр.: 23 назв.] | ||
| 330 | |a The article based on the experimental data and it describes the development of a rational design of an oscillatory system for controlled vibrational feeding of bulk materials during their heat treatment in furnaces with a vibratory base plate, which, together with the moving trolley on elastic connections, is the basis to transfer bulk material in the thermal field of an electric heating system with set processing time. To create nonsymmetric oscillations and to obtain unidirectional material motion at the horizontal furnace position, the conical springs are used. They should provide a gently inclined resonant peak, which can significantly reduce the sensitivity of the oscillating system to fluctuations of the natural frequency and excitation frequency, stiffness, friction and other factors under high temperatures and instability of the electrical network. However, the total elastic characteristic of the oscillatory system which is obtained as a result of the experiments consists of conical and cylindrical springs and shows a weakly expressed nonlinearity. Therefore, to achieve a transport effect it will require the installation of the entire furnace unit at an angle to the horizon. According to the available experimental data, a linear model of the oscillatory system was utilized. | ||
| 330 | |a В статье на основе экспериментальных данных описана разработка рациональной конструкции колебательной системы для регулируемой вибрационной подачи сыпучих материалов при их термообработке в печах с вибрационной опорной плитой, которая вместе с подвижной тележкой на упругих связях является основой для переноса сыпучих материалов в тепловом поле электронагревательной системы с заданным временем обработки. Для создания несимметричных колебаний и получения однонаправленного движения материала в горизонтальном положении печи используются конические пружины. Они должны обеспечивать пологий наклон резонансного пика, что позволяет значительно снизить чувствительность колебательной системы к колебаниям собственной частоты и частоты возбуждения, жесткости, трению и другим факторам при высоких температурах и нестабильности электрической сети. Однако общая упругая характеристика колебательной системы, полученная в результате экспериментов, состоит из конических и цилиндрических пружин и демонстрирует слабо выраженную нелинейность. Поэтому для достижения транспортного эффекта потребуется установка всего печного агрегата под углом к горизонту. По имеющимся экспериментальным данным, была использована линейная модель колебательной системы. | ||
| 461 | |t Вестник Карагандинского университета. Серия Физика | ||
| 463 | |t № 2 (98) |v [С. 93-100] |d 2020 | ||
| 510 | 1 | |a Разработка технологии обжига сыпучих материалов на основе использования альтернативной электропечи |z rus | |
| 610 | 1 | |a труды учёных ТПУ | |
| 610 | 1 | |a электронный ресурс | |
| 610 | 1 | |a an electric furnace for bulk materials burning | |
| 610 | 1 | |a vibrating base plate | |
| 610 | 1 | |a oscillating system | |
| 610 | 1 | |a nonlinear elastic characteristic | |
| 610 | 1 | |a amplitude-frequency characteristic | |
| 610 | 1 | |a amplitude-frequency characteristic | |
| 610 | 1 | |a sensitivity of the oscillating system to external factors | |
| 610 | 1 | |a электрические печи | |
| 610 | 1 | |a обжиг | |
| 610 | 1 | |a сыпучие материалы | |
| 610 | 1 | |a колебательные системы | |
| 610 | 1 | |a амплитудно-частотные характеристики | |
| 610 | 1 | |a чувствительность | |
| 610 | 1 | |a электропечи | |
| 701 | 1 | |a Nizhegorodov |b A. I. |g Anatoliy Ivanovich | |
| 701 | 1 | |a Gavrilin |b A. N. |c Specialist in the field of mechanical engineering |c Associate Professor of Tomsk Polytechnic University, Candidate of technical sciences |f 1960- |g Aleksei Nikolaevich |3 (RuTPU)RU\TPU\pers\33397 |9 17091 | |
| 701 | 1 | |a Moyzes [Moises] |b B. B. |c specialist in the field of mechanical engineering |c Associate Professor of Tomsk Polytechnic University, Candidate of technical sciences |f 1975- |g Boris Borisovich |3 (RuTPU)RU\TPU\pers\32979 |9 16824 | |
| 701 | 1 | |a Kuvshinov |b K. A. |c specialist in the field of material science |c Senior Lecturer of Tomsk Polytechnic University |f 1983- |g Kirill Alexandrovich |3 (RuTPU)RU\TPU\pers\42378 |9 21523 | |
| 712 | 0 | 2 | |a Национальный исследовательский Томский политехнический университет |b Инженерная школа новых производственных технологий |b Отделение материаловедения |3 (RuTPU)RU\TPU\col\23508 |
| 712 | 0 | 2 | |a Национальный исследовательский Томский политехнический университет |b Инженерная школа неразрушающего контроля и безопасности |b Отделение контроля и диагностики |3 (RuTPU)RU\TPU\col\23584 |
| 801 | 1 | |a RU |b 63413507 |c 20130530 | |
| 801 | 2 | |a RU |b 63413507 |c 20210907 |g RCR | |
| 856 | 4 | |u http://earchive.tpu.ru/handle/11683/80973 |z http://earchive.tpu.ru/handle/11683/80973 | |
| 856 | 4 | |u https://doi.org/10.31489/2020Ph2/93-100 | |
| 942 | |c CF | ||