The effect of phase transformations on the recovery of pulsed electron beam irradiated Ti-6Al-4V titanium alloy during scratching; Journal of Alloys and Compounds; Vol. 795

The effect of phase transformations on the recovery of pulsed electron beam irradiated Ti-6Al-4V titanium alloy during scratching; Journal of Alloys and Compounds; Vol. 795

Bibliografische gegevens
Parent link:	Journal of Alloys and Compounds Vol. 795.— 2019.— [P. 275-283]
Andere auteurs:	Sinyakova E. A. Elena Aleksandrovna, Panin A. V. Alexey Viktorovich, Perevalova O. B. Olga Borisovna, Shugurov A. R. Artur Rubinovich, Kalashnikov M. P. Mark Petrovich, Teresov A. D. Anton Dmitrievich
Samenvatting:	Title screen The formation of martensitic a' and a'' phases in Ti-6Al-4V titanium alloy subjected to low energy high current pulsed electron beam (LEHCPEB) treatment with an energy density of 12–25?J/cm2 was revealed by X-ray diffraction and transmission electron microscopy. It was substantiated that the strain-induced phase transformation is the dominant mechanism underlying the deformation behavior of the melted surface layer of the titanium alloy samples during nanoindentation and scratch testing. It was found that the reverse transformation of the a'' phase into the more close-packed a phase is responsible for the softening of the uppermost surface layer of the samples subjected to LEHCPEB treatment. The development of the direct and reverse a''?a?a'' martensitic transformations in the uppermost surface layer resulted in the improvement in elastic recovery of the treated Ti-6Al-4V samples after scratching.
Taal:	Engels
Gepubliceerd in:	2019
Onderwerpen:	электронный ресурс труды учёных ТПУ titanium alloy LEHCPEB treatment nanoindentation scratch test martensite transformations X-ray TEM титановые сплавы наноиндентирование скретч-тестирование мартенситные превращения рентгеновские снимки
Online toegang:	https://doi.org/10.1016/j.jallcom.2019.04.320
Formaat:	Elektronisch Hoofdstuk
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=664237

Gelijkaardige items

Recovery of Scratch Grooves in Ti-6Al-4V Alloy Caused by Reversible Phase Transformations; Metals; Vol. 10, iss. 10
Gepubliceerd in: (2020)

Effect of Ultrasonic Impact Treatment on Structural Phase Transformations in Ti-6Al-4V Titanium Alloy; Physical Mesomechanics; Vol. 25, iss. 3
Gepubliceerd in: (2022)

Improvement of CoCr Alloy Characteristics by Ti-Based Carbonitride Coatings Used in Orthopedic Applications; Coatings; Vol. 10, iss. 5
Gepubliceerd in: (2020)

Numerical study of atomic scale deformation mechanisms of Ti grains with different crystallographic orientation subjected to scratch testing; Applied Surface Science; Vol. 471
Gepubliceerd in: (2019)

The Role of Grain Boundaries in Rotational Deformation in Polycrystalline Titanium under Scratch Testing; Physical Mesomechanics; Vol. 22, iss. 5
Gepubliceerd in: (2019)

Использование эффекта сверхэластичности при разработке внутрисосудистых медицинских имплантатов из сплавов на основе никелида титана; Известия Томского политехнического университета [Известия ТПУ]; Т. 325, № 3 : Химия и химические технологии
Gepubliceerd in: (2014)

Effect of hydrogen redistribution during aging on the structure and phase state of nanocrystalline and coarse-grained TiNi alloys; Journal of Alloys and Compounds; Vol. 751
Gepubliceerd in: (2018)

The Effect of Hydrogen on Martensite Transformations and the State of Hydrogen Atoms in Binary TiNi-Based Alloy with Different Grain Sizes; Materials; Vol. 12 iss. 23
Gepubliceerd in: (2019)

Studies of kinetic plasticity effect in high-speed steels under Martensite transformation; Solid State Phenomena; Vol. 303
door: Demenkova L. G. Larisa Gennadievna
Gepubliceerd in: (2020)

Microstructure, phase composition and hardness of Ti–Au cladding deposited on Ti–6Al–4V substrate by electron beam powder bed fusion method; Vacuum; Vol. 203
Gepubliceerd in: (2022)

Кристаллогеометрия структур в системах Ti-Ni, Ti-Fe и Ti-Ni-Fe; Фундаментальные проблемы современного материаловедения; Т. 6, № 4
Gepubliceerd in: (2009)

Effect of Conditions of the Pulsed Plasma-chemical Synthesis on Physicochemical Properties of the CuxOy/TiO2 Nanocomposite; Current Nanomaterials; Vol. 7, iss. 3
Gepubliceerd in: (2022)

Transformations of the Microstructure and Phase Compositions of Titanium Alloys during Ultrasonic Impact Treatment Part III: Combination with Electrospark Alloying Applied to Additively Manufactured Ti-6Al-4V Titanium Alloy; Metals; Vol. 13, iss. 5
Gepubliceerd in: (2023)

The effect of crystallographic grain orientation of polycrystalline Ti on ploughing under scratch testing; Wear; Vol. 408-409
Gepubliceerd in: (2018)

The High-Temperature In Situ Synchrotron Study of the Structural-Phase Transformations in 3D-Printed Ti–6Al–4V and Ti–5Al–3Mo–V Titanium Alloys; Physics of Metals and Metallography; Vol. 125, iss. 9
Gepubliceerd in: (2024)

The Effect of Heat Treatment on the Microstructure and Phase Composition of Wrought and 3D-Printed Ti–5Al–3Mo–1V Titanium Alloy Samples; Journal of Surface Investigation: X-ray, Synchrotron and Neutron Techniques; Vol. 17, Suppl. 1
Gepubliceerd in: (2023)

Improvement of Mechanical Properties and Adhesion of Ti-Al-Si-N Coatings by Alloying with Ta; Lubricants; Vol. 10 iss. 8
Gepubliceerd in: (2022)

Transformations of the Microstructure and Phase Compositions of Titanium Alloys during Ultrasonic Impact Treatment. Part I. Commercially Pure Titanium; Metals; Vol. 11, iss. 4
Gepubliceerd in: (2021)

Mesoscopic Structural States at the Nanoscale in Surface Layers of Titanium and Its Alloy Ti-6Al-4V in Ultrasonic and Electron Beam Treatment; Physical Mesomechanics; Vol. 22, iss. 5
Gepubliceerd in: (2019)

Correlation between structural and mechanical properties of RF magnetron sputter deposited hydroxyapatite coating; Materials Characterization; Vol. 142
Gepubliceerd in: (2018)

Changes in the Structural-Phase State and Dislocation Density of Ti49.8Ni50.2 Alloy Depending on the Isochronal Annealing Temperature after Severe Plastic Deformation by abc Pressing at 573 K; Physical Mesomechanics; Vol. 27, iss. 2
Gepubliceerd in: (2024)

Increasing the Fatigue Durability of an 3D-Printed Ti-6Al-4V Alloy Electron-Beam Welded Joint by Ultrasonic Electropulsing Shock Treatment; Physics of Metals and Metallography; Vol. 123, iss. 12
Gepubliceerd in: (2022)

Molecular dynamics study of dislocation-twin boundary interaction in titanium subjected to scratching; Materials Science and Engineering: A; Vol. 800
Gepubliceerd in: (2021)

Hydrogen diffusion and the effect of hydrogen on structural transformations in binary TiNi based alloys; International Journal of Hydrogen Energy; Vol. 44, iss. 55
Gepubliceerd in: (2019)

Effect of the Lattice Curvature of Ti-6Al-4V Titanium Alloy on Their Fatigue Life and Fracture Toughness; Physical Mesomechanics; Vol. 23, iss. 5
Gepubliceerd in: (2020)

Structure and Deformation Properties of Austenitic Stainless Steel; Physics of Metals and Metallography; Vol. 121, iss. 1
Gepubliceerd in: (2020)

Microstructure and scratch behavior of TiB/Ti-6Al-4V composites fabricated by wire-feed electron beam additive manufacturing; Materials Letters; Vol. 405
Gepubliceerd in: (2026)

Effect of Ultrasonic Impact Treatment on Microstructure and Fatigue Life of 3D Printed Ti–6Al–4V Titanium Alloy; Physics of Metals and Metallography; Vol. 124, iss. 10
Gepubliceerd in: (2023)

Рентгенодифракционные исследования структурно-фазовых состояний в поверхностных слоях никелида титана, модифицированных электронно-пучковой обработкой; Известия Томского политехнического университета [Известия ТПУ]; Т. 324, № 3 : Химия и химические технологии
Gepubliceerd in: (2014)

The Effect of Nanoscale Mesoscopic Structural States Associated with Lattice Curvature on the Mechanical Behavior of Ti–6Al–4V Alloy; Physical Mesomechanics; Vol. 23, iss. 6
Gepubliceerd in: (2020)

Synthesis of titanium diboride by electric arc plasma in air; Materials Chemistry and Physics; Vol. 328
Gepubliceerd in: (2024)

Effect of Structural-Phase State on the Deformation Behavior and Mechanical Properties of Near β Titanium Alloy VT22 in the Temperature Range 293–823 K; Physical Mesomechanics; Vol. 27, iss. 1
Gepubliceerd in: (2024)

Исследование структуры и физико-механических свойств керамики на основе оксинитридов алюминия и циркония; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 333, № 2
Gepubliceerd in: (2022)

Sintered Silicon Carbide composites deposited on zirconium alloy substrates in air and Ar atmosphere – Part I: Evaluation of scratch adhesion and tribology properties; Materials Letters; Vol. 306
Gepubliceerd in: (2022)

Основы работы в среде программирования Scratch учебно-методическое пособие
door: Гербут С. С.
Gepubliceerd in: (Тула, ТГПУ, 2018)

Change in the Phase Composition and Lattice Parameters of the Solid Solution Based on a-Ti in the Surface Layers of the Ti–6Al–4V Alloy Subjected to Electron-Beam Treatment; Physics of Metals and Metallography; Vol. 121, iss. 2
door: Perevalova O. B. Olga Borisovna
Gepubliceerd in: (2020)

Effect of Heat Input on the Microstructure and Phase Composition of Additively Manufactured Ti–6Al–4V Alloy; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 18, iss. 6
door: Kamelina K. D. Kristina Dmitrievna
Gepubliceerd in: (2024)

The structure - phase state and microhardness of the surface layer of the VT1-0 titanium alloys treated by copper ions; Vacuum; Vol. 149
Gepubliceerd in: (2018)

Structural-phase state and mechanical properties of submicrocrystalline titanium alloy Ti-6Al-4V obtained with use of reversible hydrogen alloying; Bulletin of the Tomsk Polytechnic University; Vol. 311, № 2
door: Grabovetskaya G. P. Galina Petrovna
Gepubliceerd in: (2007)

Microstructure and Mechanical Properties of Ti–Al–Ta–N Coatings Alloyed with Si; Russian Physics Journal; Vol. 65, iss. 10
Gepubliceerd in: (2023)