Alumina-based composites reinforced with single-walled carbon nanotubes; IOP Conference Series: Materials Science and Engineering; Vol. 511 : Perspective Materials of Constructional and Medical Purpose

Alumina-based composites reinforced with single-walled carbon nanotubes; IOP Conference Series: Materials Science and Engineering; Vol. 511 : Perspective Materials of Constructional and Medical Purpose

Detaylı Bibliyografya
Parent link:	IOP Conference Series: Materials Science and Engineering Vol. 511 : Perspective Materials of Constructional and Medical Purpose.— 2019.— [012001, 6 p.]
Yazar:	Leonov A. A. Andrey Andreevich
Müşterek Yazar:	National Research Tomsk Polytechnic University (TPU)
Diğer Yazarlar:	Abdulmenova E. V. Ekaterina Vladimirovna
Özet:	Title screen Monolithic Al[2]O[3] ceramics and Al[2]O[3] - 3 vol% single-walled carbon nanotubes (SWCNTs) composites were prepared by spark plasma sintering. The influence of SWCNTs and sintering temperature on sintering behavior and mechanical properties were investigated. Nanotubes were relatively homogeneously distributed in the composite powder, although some agglomerates/bundles existed. It was found that SWCNTs addition retards slightly the sinterability of alumina by nanotubes hindering of particle rearrangement. The average microhardness of the composites was lower than that of Al[2]O[3] ceramics, but there were also high microhardness values of composites (20.41 GPa). The reduction in microhardness is explained in this paper. The average values of the fracture toughness (4.94 MPa·m{1/2}) from the composite sintered at 1500 °C were approximately 6 % and 12 % higher than those from the Al[2]O[3] ceramics sintered at 1500 °C and 1600 °C, respectively. In addition, the analysis of the phase composition and the parameters of the crystal structure of the samples were made.
Dil:	İngilizce
Baskı/Yayın Bilgisi:	2019
Konular:	электронный ресурс труды учёных ТПУ композиты оксид алюминия армирование углеродные нанотрубки спекание микротвердость фазовый состав кристаллические структуры
Online Erişim:	http://dx.doi.org/10.1088/1757-899X/511/1/012001 http://earchive.tpu.ru/handle/11683/55431
Materyal Türü:	Elektronik Kitap Bölümü
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=660529

Benzer Materyaller

Ceramic composite based on zirconia reinforced by single-walled carbon nanotubes; Nanotechnologies in Russia; Vol. 14, iss. 3-4
Baskı/Yayın Bilgisi: (2019)

Spark plasma sintering of ceramic matrix composite based on alumina, reinforced by carbon nanotubes; IOP Conference Series: Materials Science and Engineering; Vol. 286 : Modern Technologies and Materials of New Generations (MTMNG-2017)
Baskı/Yayın Bilgisi: (2018)

Defect Evolution of Ion-Exposed Single-Wall Carbon Nanotubes; Journal of Physical Chemistry C; Vol. 123, iss. 4
Baskı/Yayın Bilgisi: (2018)

Biofiber Reinforcement in Composite Materials
Baskı/Yayın Bilgisi: (Amsterdam, Elsevier, 2015)

Raman Spectroscopy Investigation of Laser-Irradiated Single-Walled Carbon Nanotube Films; Physica Status Solidi (B); Vol. 256, iss. 2
Yazar:: Rodriguez (Rodriges) Contreras R. D. Raul David
Baskı/Yayın Bilgisi: (2019)

Application of 3D Computed Microtomography for Investigating the Microstructural Defects of Carbon Fiber Reinforced Composite Made by 3D-Printing; Key Engineering Materials; Vol. 712 : Advanced Materials for Technical and Medical Purpose (AMTMP 2016)
Baskı/Yayın Bilgisi: (2016)

Механические свойства композита на основе Al[2]O[3], армированного одностенными углеродными нанотрубками; Функциональные материалы: разработка, исследование, применение
Yazar:: Данченко В. А.
Baskı/Yayın Bilgisi: (2018)

Impact of Multi-Walled Carbon Nanotubes to Rye Seedlings; Advanced Materials Research; Vol. 1085 : Prospects of Fundamental Sciences Development (PFSD-2014)
Baskı/Yayın Bilgisi: (2015)

Carbon Nanotubes and Graphene
Baskı/Yayın Bilgisi: (Amsterdam, Elsevier, 2014)

Electrical Properties of Carbon Nanotube-Reinforced Polymer Composites; Key Engineering Materials; Vol. 685 : High Technology: Research and Applications 2015 (HTRA 2015)
Baskı/Yayın Bilgisi: (2016)

Arc-produced short-length multi-walled carbon nanotubes as “millstones” for the preparation of graphene-like nanoplatelets; Carbon; Vol. 146
Baskı/Yayın Bilgisi: (2019)

Физико-механические свойства нанокомпозитов на основе ZrO[2], армированных одностенными углеродными нанотрубками; Перспективы развития фундаментальных наук; Т. 1 : Физика
Yazar:: Цуканов В. А.
Baskı/Yayın Bilgisi: (2018)

Conductive carbon nanotube-reinforced polymer composites and their characterization; IEEE Transactions on Dielectrics and Electrical Insulation; Vol. 23, iss. 3
Baskı/Yayın Bilgisi: (2016)

Fatigue behaviour of CG and UFG titanium: DIC and fractography studies; IOP Conference Series: Materials Science and Engineering; Vol. 511 : Perspective Materials of Constructional and Medical Purpose
Yazar:: Eremin A. V. Alexandr Vyacheslavovich
Baskı/Yayın Bilgisi: (2019)

Influence of Anodization Time and Voltage on the Parameters of TiO[2] Nanotubes; IOP Conference Series: Materials Science and Engineering; Vol. 116 : Advanced Materials and New Technologies in Modern Materials Science
Yazar:: Chernozem R. V. Roman Viktorovich
Baskı/Yayın Bilgisi: (2016)

Исследование слоистых базальтопластиков с дополнительным армированием углеродными нанотрубками; Перспективные материалы конструкционного и функционального назначения
Yazar:: Ху Синь
Baskı/Yayın Bilgisi: (2022)

Спарк-плазменное спекание керамоматричного композита на основе Al[2]O[3], армированного углеродными нанотрубками; Современные технологии и материалы новых поколений
Baskı/Yayın Bilgisi: (2017)

Measurement Affecting Errors in Digital Image Correlation; IOP Conference Series: Materials Science and Engineering; Vol. 511 : Perspective Materials of Constructional and Medical Purpose
Yazar:: Titkov V. V.
Baskı/Yayın Bilgisi: (2019)

Morphometric Parameters and Biochemical Status of Oilseed Rape Exposed to Fine-Dispersed Metallurgical Sludge, PHMB-Stabilized Silver Nanoparticles and Multi-Wall Carbon Nanotubes; Advanced Materials Research : Advanced materials, synthesis, development and application; Vol. 880 : Prospects of Fundamental Sciences Development (PFSD-2013)
Baskı/Yayın Bilgisi: (2014)

In situ estimation of fatigue crack parameters by digital image correlation under cyclic loading with single overload; IOP Conference Series: Materials Science and Engineering; Vol. 511 : Perspective Materials of Constructional and Medical Purpose
Baskı/Yayın Bilgisi: (2019)

Получение армированных углеродными нанотрубками и нановолокнами Al[2]O[3] композитов на основе ZrO[2] с повышенной трещиностойкостью; Научная инициатива иностранных студентов и аспирантов российских вузов
Yazar:: Ли Цзин
Baskı/Yayın Bilgisi: (2020)

Армированная нановолокнами Al[2]O[3] и углеродными нанотрубками циркониевая керамика с повышенной трещиностойкостью; Химия и химическая технология в XXI веке
Yazar:: Ли Цзин
Baskı/Yayın Bilgisi: (2020)

Ultrasonic testing method for quality control of mold castings; IOP Conference Series: Materials Science and Engineering; Vol. 511 : Perspective Materials of Constructional and Medical Purpose
Yazar:: Bolotina I. O. Irina Olegovna
Baskı/Yayın Bilgisi: (2019)

Carbon nanotubes science and applications
Baskı/Yayın Bilgisi: (Boca Raton, CRC Press, 2005)

The Effect of High-Energy Ball Milling Conditions on Microstructure and Hydrogen Desorption Properties of Magnesium Hydride and Single-Walled Carbon Nanotubes; Metals; Vol. 11, iss. 9
Yazar:: Kudiyarov V. N. Victor Nikolaevich
Baskı/Yayın Bilgisi: (2021)

Fabrication and characterization of hybrid nanostructure biocomposites based on oxide nanotubes; Перспективы развития фундаментальных наук
Yazar:: Чернозем Р. В. Роман Викторович
Baskı/Yayın Bilgisi: (2015)

Boron Nitride Nanotubes Versus Carbon Nanotubes: A Thermal Stability and Oxidation Behavior Study; Nanomaterials; Vol. 10, iss. 12
Baskı/Yayın Bilgisi: (2020)

Flexural properties of copper-filled carbon fiber reinforced polymers; IOP Conference Series: Materials Science and Engineering; Vol. 1118 : Mechanical Engineering and Modern Technologies (MEMT 2020)
Yazar:: Eremin A. V. Alexandr Vyacheslavovich
Baskı/Yayın Bilgisi: (2021)

Graphene nanoribbon winding around carbon nanotube; Computational Materials Science; Vol. 135
Baskı/Yayın Bilgisi: (2017)

Керамические композиты на основе ZrO[2], армированные углеродными нанотрубками (УНТ); Научная инициатива иностранных студентов и аспирантов российских вузов
Yazar:: Лю Хаоцэ
Baskı/Yayın Bilgisi: (2020)

Radiation modification of Ni nanotubes by electrons; Materials Research Express; Vol. 4, iss. 10
Baskı/Yayın Bilgisi: (2017)

Destruction of LED heterostructures under high-current electron beam irradiation; IOP Conference Series: Materials Science and Engineering; Vol. 511 : Perspective Materials of Constructional and Medical Purpose
Yazar:: Zixuan Li
Baskı/Yayın Bilgisi: (2019)

Electrochemical hydrogenation after mechanical activated near equiatomic Ti-Ni powder; IOP Conference Series: Materials Science and Engineering; Vol. 511 : Perspective Materials of Constructional and Medical Purpose
Yazar:: Abdulmenova E. V. Ekaterina Vladimirovna
Baskı/Yayın Bilgisi: (2019)

The effects of liquid-phase oxidation of multiwall carbon nanotubes on their surface characteristics; IOP Conference Series: Materials Science and Engineering; Vol. 112 : Fundamental Aspects of Rare-earth Elements Mining and Separation and Modern Materials Engineering (REES-2015)
Baskı/Yayın Bilgisi: (2016)

Chain Model for Carbon Nanotube Bundle under Plane Strain Conditions; Materials; Vol. 12 iss. 23
Baskı/Yayın Bilgisi: (2019)

Development of personalized approach to the reconstruction of bone tissue defects using porous ceramic osteoimplants; IOP Conference Series: Materials Science and Engineering; Vol. 511 : Perspective Materials of Constructional and Medical Purpose
Baskı/Yayın Bilgisi: (2019)

The relation between the inductive capacity of an oxide surface structure of hard alloys and their wear resistance; IOP Conference Series: Materials Science and Engineering; Vol. 511 : Perspective Materials of Constructional and Medical Purpose
Baskı/Yayın Bilgisi: (2019)

Thermogravimetric analysis of epoxy-based carbon fiber reinforced polymers modified by carbon fillers; IOP Conference Series: Materials Science and Engineering; Vol. 1118 : Mechanical Engineering and Modern Technologies (MEMT 2020)
Yazar:: Burkov M. V. Mikhail Vladimirovich
Baskı/Yayın Bilgisi: (2021)

Thermal Stability and Flammability of Epoxy Composites Filled with Multi-Walled Carbon Nanotubes, Boric Acid, and Sodium Bicarbonate; Polymers; Vol. 13, iss. 4
Baskı/Yayın Bilgisi: (2021)

Mechanical and Tribotechnical Properties of Polyphenylene Sulfide Composites Reinforced with Carbon Fibers of Various Dimension; AIP Conference Proceedings; Vol. 2051 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2018 (AMHS’18)
Baskı/Yayın Bilgisi: (2018)