Influence of the Cobalt Additive on the Flux Cored Wire of System Fe-C-Si-Mn-Cr-Ni-Mo-V; Key Engineering Materials; Vol. 736 : Materials and their Application

Influence of the Cobalt Additive on the Flux Cored Wire of System Fe-C-Si-Mn-Cr-Ni-Mo-V; Key Engineering Materials; Vol. 736 : Materials and their Application

Bibliographic Details
Parent link:	Key Engineering Materials: Scientific Journal Vol. 736 : Materials and their Application.— 2017.— [P. 63-67]
Corporate Author:	Национальный исследовательский Томский политехнический университет (ТПУ) Юргинский технологический институт (филиал) (ЮТИ) Кафедра металлургии и черных металлов (МЧМ)
Other Authors:	Osetkovskiy I. V., Kozyrev N. A., Gusev A. I., Kozyreva O. A., Gizatulin R. A. Rinat Akramovich, Valueva A. V. Anna Vladimirovna
Summary:	Title screen Studied the effect of the introduction of cobalt into the charge powder fused wire system Fe-C-Si-Mn-Cr-Ni-Mo-V, used in cladding assemblies and equipment parts and mechanisms operating under abrasive and abrasive shock loads., the samples cored wires were manufactured in the laboratory conditions using appropriate powder materials and as a carbonfluoride contained material were used the dust from gas purification of aluminum production. Режим доступа: по договору с организацией-держателем ресурса
Language:	English
Published:	2017
Subjects:	электронный ресурс труды учёных ТПУ abrasive shock loads dependencies hardness multivariate analysis non-metalic inclusions recovering surfacing wear resistance wire ударные нагрузки твердость многомерный анализ восстановление зависимость наплавки неметаллические включения износостойкость проволока
Online Access:	http://dx.doi.org/10.4028/www.scientific.net/KEM.736.63
Format:	Electronic Book Chapter
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=656917

Similar Items

Quality of Metal Deposited Flux Cored Wire with the System Fe-C-Si-Mn-Cr-Mo-Ni-V-Co; Key Engineering Materials; Vol. 736 : Materials and their Application
Published: (2017)

Technological Improvement of Surfacing of Parts of Hammer Crushers Used in Coke-Chemical Industry; Materials Science Forum; Vol. 927 : Materials and Processing Technology II
Published: (2018)

Strengthening of Metallurgical Equipment Parts by Plasma Surfacing in Nitrogen Atmosphere; Metallurgist; Vol. 65, iss. 11-12
Published: (2022)

Refractory ceramics based on magnesium–aluminate spinel and periclase of the Satka deposit; Materials Chemistry and Physics; Vol. 313
Published: (2024)

Физико-механические аспекты абразивного изнашивания сталей в условиях охлажденной воздушной среды; Обработка металлов (технология, оборудование, инструменты); Т. 21, № 1
by: Ан И-Кан
Published: (2019)

The effect of counterbody on tribological adaptation of an electron beam deposited HSS M2 steel coating in a range of sliding speeds and normal loads; Tribology International; Vol. 161
by: Gnyusov S. F. Sergey Fedorovich
Published: (2021)

Fracture toughness and abrasive wear of (ZrTi)B2–SiC ceramic composites with low-modulus hexagonal boron nitride inclusions; Ceramics International; Vol. 51, iss. 18, Pt. B
Published: (2025)

Investigation of the welded layer hardness at restoration of electric motor shafts; Journal of Applied Engineering Science; Vol. 23, iss 2
Published: (2025)

О снижении уровня неопределенности при управлении заводнением залежей с трудноизвлекаемыми запасами; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 331, № 5
by: Мухаметшин В. В. Вячеслав Вячеславович
Published: (2020)

Анализ эффективности технологии водного HUFF and PUFF на основе мирового опыта применения и лабораторных исследований; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 334, № 4
by: Цыкунов О. И. Олег Игоревич
Published: (2023)

Tourism as a «post-staples» diversification for Russian remote resource-dependent regions: a new path for Kuzbass; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 330, № 10
Published: (2019)

Analysis of the efficiency of the application of binary mixtures technology for the development of hard-to-recover fields of Western Siberia; Journal of Economics and Social Sciences; № 16
by: Konovalov A. A. Andrey
Published: (2020)

Special Features of Large-Size Resistors for High-Voltage Pulsed Installations; AIP Conference Proceedings; Vol. 1909 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2017 (AMHS’17)
by: Minakova N. N.
Published: (2017)

Comparative study of shock-wave hardening and substructure evolution of 304L and Hadfield steels irradiated with a nanosecond relativistic high-current electron beam; Journal of Alloys and Compounds; Vol. 714
Published: (2017)

Improvement of Research Procedures into the Highly Rigid Welded Metal Using Thermal Microscopy Facilities; Materials Science Forum; Vol. 927 : Materials and Processing Technology II
Published: (2018)

Комбинированные технологии добычи трудноизвлекаемых георесурсов; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 336, № 12
Published: (2025)

Оценка влияния особенностей размещения производительных сил, инфраструктуры и объектов социальной сферы на результативность экономической деятельности предприятий в муниципальных образованиях Уральского федерального округа; Векторы благополучия: экономика и социум; Т. 52, № 4
by: Наумов И. В. Илья Викторович
Published: (2024)

Additive Manufacturing of Metal Products via Filler Wire Arc Welding (Review); Materials Science Forum; Vol. 1064
Published: (2022)

Energy Flux at the Substrate During Dual Magnetron Sputtering of TiAlN Coating; Russian Physics Journal; № 11 - Vol. 65
Published: (2023)

Tribological properties of alloyed TiSi-stainless steel carbide coatings deposited by reactive cathodic arc method; Wear; Vol. 460-461
Published: (2020)

Increasing the Fatigue Durability of an 3D-Printed Ti-6Al-4V Alloy Electron-Beam Welded Joint by Ultrasonic Electropulsing Shock Treatment; Physics of Metals and Metallography; Vol. 123, iss. 12
Published: (2022)

Статистический анализ качества трудноизвлекаемых нефтей; Известия Томского политехнического университета [Известия ТПУ]; Т. 326, № 4
by: Ященко И. Г. Ирина Германовна
Published: (2015)

Технология бинарных смесей как современный комплексный метод увеличения нефтеотдачи для разработки трудноизвлекаемых запасов на месторождениях Западной Сибири; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 334, № 9
Published: (2023)

Multi-Pass Laser and Hybrid Laser-Arc Narrow-Gap Welding of Steel Butt Joints; Materials Science Forum; Vol. 927 : Materials and Processing Technology II
Published: (2018)

Production of Iron Nanopowders by the Electric Explosion of Wire; Advanced Materials Research; Vol. 1097
by: Pustovalov A. V. Aleksey Vitalievich
Published: (2015)

Research of Contact Stresses Distribution on Plunge-Cutting into a Steel Workpiece; Key Engineering Materials; Vol. 769 : High Technology: Research and Applications (HTRA 2017)
Published: (2018)

Технология разработки неоднородной залежи массивного типа с газонефтяным и водонефтяным контактами; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 333, № 4
Published: (2022)

Multifunctional Ti based carbonitride coatings for applications in severe environments; Thin Solid Films; Vol. 682
Published: (2019)

Carbide-nanopowders produced by electrical explosion of wires; Journal of optoelectronics and advanced materials; Vol. 9, № 5
by: Ilyin A. P. Aleksandr Petrovich
Published: (2007)

Effect of the gas composition at the electrical explosion of wires on the nanopowders properties; Advanced Materials Research; Vol. 872
by: Nazarenko O. B. Olga Bronislavovna
Published: (2013)

The Development of Technology of Basalt Nanocomposite Coatings Detonation-Gas Spaying on the Disk ("Target") Basis of Thin Layer Magnetron Spaying Equipment; Materials Science Forum; Vol. 927 : Materials and Processing Technology II
Published: (2018)

Разработка стенда исследования процесса гашения ударной нагрузки; Информационные технологии (IT) в контроле, управлении качеством и безопасности
Published: (2019)

Оценка параметров разрушающей нагрузки при ударно-волновом нагружении для ответственных строительных конструкций сооружений нефтегазового комплекса; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 328, № 3
by: Однокопылов Г. И. Георгий Иванович
Published: (2017)

Разработка базовой технологии выемки ископаемого с поворотом конвейера на 90°; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 329, № 8
Published: (2018)

Use of Refractory Nanoparticles as a Component of Welding Materials in Welding and Surfacing With Coated Electrodes and Flux Cored Wires; IOP Conference Series: Materials Science and Engineering; Vol. 142 : Innovative Technologies in Engineering
by: Karthev D. S. Dmitry Sergeevich
Published: (2016)

Calculation of Contact Stresses during Titanium Alloy Cutting; Key Engineering Materials; Vol. 769 : High Technology: Research and Applications (HTRA 2017)
Published: (2018)

Influence of the Properties of Surface Polyoxide Structures on Wear Processes in Solid Bodies; Inorganic Materials: Applied Research; Vol. 11, iss. 4
Published: (2020)

Dynamic model of elastoplastic contact interaction of smooth bodies; Bulletin of the Tomsk Polytechnic University; Vol. 310, № 2
by: Maximenko А. А.
Published: (2007)

Цифровая модель износа конвективных поверхностей теплообмена пылеугольного котла; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 333, № 4
by: Тюрина Э. А. Элина Александровна
Published: (2022)

Integrated Quality Ensuring Technique of Plasma Wear Resistant Coatings; Key Engineering Materials; Vol. 736 : Materials and their Application
Published: (2017)