Composite materials based on high-modulus compounds for additive technology; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies

Composite materials based on high-modulus compounds for additive technology; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies

Podrobná bibliografie
Parent link:	IOP Conference Series: Materials Science and Engineering Vol. 140 : Interdisciplinary Problems in Additive Technologies.— 2016.— [012009, 11 p.]
Korporace:	Национальный исследовательский Томский политехнический университет (ТПУ) Институт физики высоких технологий (ИФВТ) Кафедра материаловедения и технологии металлов (МТМ), Национальный исследовательский Томский политехнический университет (ТПУ) Институт физики высоких технологий (ИФВТ) Кафедра материаловедения в машиностроении (ММС)
Další autoři:	Grigoriev M. V. Mikhail Vladimirovich, Kotelnikov N., Buyakova S. P. Svetlana Petrovna, Kulkov S. N. Sergey Nikolaevich
Shrnutí:	Title screen The effect of adding nanocrystalline ZrO[2] and submicron TiC to ultrafine Al[2]O[3] on mechanical properties and the microstructure of the composites developed by hot pressing was investigated. It was shown that by means of hot pressing in argon atmosphere at the sintering temperature of 1500 °C one can obtain the composites of Al[2]O[3]-ZrO[2]-TiC with a fine structure and minimal porosity. It was shown that in the material a multi-scale hierarchical structure is formed, which possesses high physical and mechanical properties: the hardness and fracture toughness was 22 GPa and 5.2 MPa*m1/2, respectively. It has been shown that mechanical properties of the composite are better than those of commercial composites based on aluminum oxide (Al[2]O[3], ZTA, Al[2]O[3]-TiC) and are comparable to those of silicon nitride.
Jazyk:	angličtina
Vydáno:	2016
Témata:	электронный ресурс труды учёных ТПУ композиционные материалы соединения присадки композиты горячее прессование физико-механические свойства оксид алюминия
On-line přístup:	http://dx.doi.org/10.1088/1757-899X/140/1/012009 http://earchive.tpu.ru/handle/11683/34863
Médium:	Elektronický zdroj Kapitola
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=650714

Podobné jednotky

The influence of ZrB[2]-SiC powders mechanical treatment on the structure of sintered ceramic composites; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Vydáno: (2016)

The Structure and Properties of Composites Al[2]O[3]-ZrO[2]-TiC for Use in Extreme Conditions; AIP Conference Proceedings; Vol. 1683 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures
Vydáno: (2015)

Problems of Development and Application of Metal Matrix Composite Powders for Additive Technologies; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Vydáno: (2016)

Композиционные материалы нового покаления Al[2]O[3]-ZrB[2] с добавлением 30% карбида кремния; Современные технологии и материалы новых поколений
Autor: Грикова А. А.
Vydáno: (2017)

Multicomponent Antifriction Composite Based on Extrudable Matrix "UHMWPE - HDPE-g-VTMS - PP" for Additive Manufacturing; IOP Conference Series: Materials Science and Engineering; Vol. 795 : Mechanical Engineering and Modern Technologies (MEMT2019)
Vydáno: (2020)

Development of bioceramic material for spinal surgery implants; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Vydáno: (2016)

Свойства перспективных конструкционных материалов для термоядерного реактора; Атомная техника за рубежом; № 3
Autor: Бронников В. А.
Vydáno: (2003)

Coating synthesis controlled by electron-beam heating; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Autor: Gordienko A. I. Anatoly Illarionovich
Vydáno: (2016)

Numerical analysis of initial stage of thermal shock; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Autor: Demidov V. N. Valery Nikolaevich
Vydáno: (2016)

Mathematical modelling of thermal and kinetic phenomena in electron-beam technologies; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Autor: Knyazeva A. G. Anna Georgievna
Vydáno: (2016)

The development of additive technologies for production of ceramic components and parts of a new type by means of selective laser melting; Современные технологии и материалы новых поколений
Autor: Kolmakov S. V.
Vydáno: (2017)

Microstructure, mechanical properties and machining performance of hot-pressed Al[2]O[3]-ZrO[2]-TiC composites; IOP Conference Series: Materials Science and Engineering; Vol. 116 : Advanced Materials and New Technologies in Modern Materials Science
Vydáno: (2016)

Phase Composition and Microstructure of Ti-Nb Alloy Produced by Selective Laser Melting; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Vydáno: (2016)

Structure and thermal behavior of zirconium tungstate under heating; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Vydáno: (2016)

Mechanical Properties of Zirconium Ceramics with Hierarchical Porous Structure; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Autor: Kulkov S. N. Sergey Nikolaevich
Vydáno: (2016)

Structures Formation on the Y-TZP-AI[2]O[3] Ceramic Composites Surface; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Vydáno: (2016)

Vol. 140 : Interdisciplinary Problems in Additive Technologies: International Seminar, 16–17 December 2015, Tomsk, Russia; [proceedings]; IOP Conference Series: Materials Science and Engineering
Vydáno: (2016)

Aluminium oxide-hydroxides obtained by hydrothermal synthesis: influence of thermal treatment on phase composition and textural characteristics; IOP Conference Series: Materials Science and Engineering; Vol. 98 : Interdisciplinary Problems of Nanotechnology, Biomedicine and Nanotoxicology (Nanobiotech 2015)
Vydáno: (2015)

Разработка составов и технологии получения алюмоциркониевой керамики повышенной прочности и износостойкости с добавками SrZrO3 и Cr2O3: диссертация на соискание ученой степени кандидата технических наук; спец. 2.6.14
Autor: Семанцова Е. С. Екатерина Станиславовна
Vydáno: (Новосибирск, 2026)

Разработка составов и технологии получения алюмоциркониевой керамики повышенной прочности и износостойкости с добавками SrZrO3 и Cr2O3: автореферат диссертации на соискание ученой степени кандидата технических наук; спец. 2.6.14
Autor: Семанцова Е. С. Екатерина Станиславовна
Vydáno: (Томск, 2026)

Investigation of adsorption properties of alumina produced by vacuum spray method; IOP Conference Series: Materials Science and Engineering; Vol. 116 : Advanced Materials and New Technologies in Modern Materials Science
Autor: Khrustaleva K.
Vydáno: (2016)

The effect of hydrogen on strain hardening and fracture mechanism of high-nitrogen austenitic steel; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Vydáno: (2016)

Технологические особенности получения оксинитрида алюминия; Современные технологии и материалы новых поколений
Vydáno: (2017)

Activation of consolidation processes of alumina ceramics; IOP Conference Series: Materials Science and Engineering; Vol. 116 : Advanced Materials and New Technologies in Modern Materials Science
Autor: Matrenin S. V. Sergey Veniaminovich
Vydáno: (2016)

Numerical Study of the Features of Ti-Nb Alloy Crystallization during Selective Laser Sintering; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Autor: Dmitriev A. I.
Vydáno: (2016)

Study of structure and physical and mechanical properties of ceramics based on aluminum oxinitride; Перспективы развития фундаментальных наук; Т. 2 : Химия
Autor: Wang Dakun
Vydáno: (2018)

Application of automated technological complexes in additive production; Междисциплинарные проблемы аддитивных технологий
Vydáno: (2017)

Process Conditions of Forming the Surface Layer of Aluminum Powder Product by Layer-by-layer Laser Sintering; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Vydáno: (2016)

X-Ray Diffraction Analysis of the Sintered Y-TZP-AI[2]O[3] Ceramics; IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Vydáno: (2016)

Mathematical Model of Three-Layer Composite Synthesis during Hot Isostatic Pressing; AIP Conference Proceedings; Vol. 1783 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2016
Autor: Knyazeva A. G. Anna Georgievna
Vydáno: (2016)

Forming a single layer of a composite powder based on the Ti-Nb system via selective laser melting (SLM); IOP Conference Series: Materials Science and Engineering; Vol. 140 : Interdisciplinary Problems in Additive Technologies
Vydáno: (2016)

Structure and Tribomechanical Properties of Multicomponent Extrudable "UHMWPE-HDPE-g-SMAPP" Composites Fabricated by Fused Deposition Modeling; AIP Conference Proceedings; Vol. 2167 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2019 (AMHS'19)
Vydáno: (2019)

Influence of metallic additives on manganese ferrites sintering; IOP Conference Series: Materials Science and Engineering; Vol. 289 : Modern Technologies for Non-Destructive Testing
Autor: Shevelev S. A. Sergey Anatolievich
Vydáno: (2018)

New Carbon-Fluorine Containing Additive for the Welding Fluxes; Applied Mechanics and Materials; Vol. 682 : Innovation Technology and Economics in Engineering
Autor: Kozyrev N. A.
Vydáno: (2014)

Activated sintering of ceramics on the basis of Al[2]O[3]; IOP Conference Series: Materials Science and Engineering; Vol. 93: Modern Technique and Technologies (MTT'2015)
Vydáno: (2015)

Alumina-based composites reinforced with single-walled carbon nanotubes; IOP Conference Series: Materials Science and Engineering; Vol. 511 : Perspective Materials of Constructional and Medical Purpose
Autor: Leonov A. A. Andrey Andreevich
Vydáno: (2019)

The additive technology in nuclear power plants; Интеллектуальные энергосистемы; Т. 3
Autor: Vergaskina M. A.
Vydáno: (2016)

Исследование механических свойств корундовой и муллито- корундовой керамики; Высокие технологии в современной науке и технике (ВТСНТ-2017)
Autor: Ван Дакунь
Vydáno: (2017)

The Analysis of Microstructure and the Properties of the Metallic-Matrix Composite on the Basis of the Copper and Aluminum Oxide; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Vydáno: (2015)

Synthesis and properties of aluminum based composite materials for high operating temperatures; Перспективные материалы с иерархической структурой для новых технологий и надежных конструкций
Autor: Vorozhtsov S.
Vydáno: (2016)