Smelting Steel Resistant to Corrosion from Metal Mixing Air in Late Oxygen Blowing; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering

Smelting Steel Resistant to Corrosion from Metal Mixing Air in Late Oxygen Blowing; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering

Manylion Llyfryddiaeth
Parent link:	Applied Mechanics and Materials: Scientific Journal Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering.— 2015.— [P. 104-107]
Awdur Corfforaethol:	Национальный исследовательский Томский политехнический университет (ТПУ) Юргинский технологический институт (филиал) (ЮТИ) Кафедра металлургии и черных металлов (МЧМ)
Awduron Eraill:	Gizatulin R. A. Rinat Akramovich, Valueva A. V. Anna Vladimirovna, Valuev D. V. Denis Viktorovich, Serikbol A.
Crynodeb:	Title screen The paper considers that the application in metallurgical enterprises-s mixing argon bath at the end of oxygen blowing in the smelting of corrosion-resistant steel has found wide application [1, 2]. However, the deficit-ness and the relatively high cost of argon, low pressure in his shop on line constrain most plants use argon at you-melting corrosion resistant steels. The article suggests that in-intensification of decarburization in the smelting of corrosion-resistant chromium-nickel steels in the 40-ton electric arc furnace use compressed air instead of argon. Режим доступа: по договору с организацией-держателем ресурса
Iaith:	Saesneg
Cyhoeddwyd:	2015
Cyfres:	Materials Science in Mechanical Engineering
Pynciau:	электронный ресурс труды учёных ТПУ углерод потребление очистка стали технологии коррозия металлов выплавка
Mynediad Ar-lein:	http://dx.doi.org/10.4028/www.scientific.net/AMM.770.104
Fformat:	Electronig Pennod Llyfr
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=643460

Eitemau Tebyg

Nitrogen Alloying of Steel by Blowing in the Ladle through Bottom and Submersible Tuyeres; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

Distributive Characteristics of Gas Phase in a Liquid when Bottom Blowing; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

Optimization of Products Life Cycle; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Petrushin S. I. Sergey Ivanovich
Cyhoeddwyd: (2015)

Prospects of Galvanic Sludge Recycling; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Filonov A. V. Alexandr Vladimirovich
Cyhoeddwyd: (2015)

Simulation of Geokhod Movement with Blade Actuator; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Sadovets V. Yu. Vladimir Yurievich
Cyhoeddwyd: (2015)

Geokhod Propel Effort Mathematical Model; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Blashchuk M. Yu. Mikhail Yurievich
Cyhoeddwyd: (2015)

Combined Steel Treatment with Calcium-Silicon; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

Determining Deviations in Geometry of the Geokhod Shells; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Valter A. V. Aleksandr Viktorovich
Cyhoeddwyd: (2015)

Preliminary Medical Studies of Electrocardiograph on Nanosensors; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Grigoriev M. G. Mikhail Georgievich
Cyhoeddwyd: (2015)

Engineering and Technology Based on Rapid Prototyping; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Saprykin A. A. Aleksandr Aleksandrovich
Cyhoeddwyd: (2015)

Microsilica as a Modifying Component in Fired Ceramics; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Torosyan V. F. Vera Fedorovna
Cyhoeddwyd: (2015)

Resilience Tests of Milling Cutters with Constructive Feed; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

On the Design of Composite Active Part of Cutting Tools; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Petrushin S. I. Sergey Ivanovich
Cyhoeddwyd: (2015)

Fiber-Reinforced Composites in Rapid Prototyping Technologies; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Saprykin A. A. Aleksandr Aleksandrovich
Cyhoeddwyd: (2015)

Controllable Decomposition in Ahm Crystals in Ultraviolet Radiation; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

Computer Simulation of Strain at Drilling with PDC Bits; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Burkov P. V. Petr Vladimirovich
Cyhoeddwyd: (2015)

Algorithm of Route Position's Detecting for Service Transport; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Savrasov F. V. Fedor Vitalievich
Cyhoeddwyd: (2015)

Application of Inorganic Nanopowders in Welding, Surfacing and Spraying (Review); Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Lukashov A. S.
Cyhoeddwyd: (2015)

Operating Mode Simulation of the Micro HPP Hydro-Generator; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

Development of the Technique to Simulate Residual Heading Corium Prototype; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Baklanov V. V. Viktor Vladimirovich
Cyhoeddwyd: (2015)

Experimental Study of Plastic Deformation Intensity in Cutting Zone; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Proskokov A. V. Andrey Vladimirovich
Cyhoeddwyd: (2015)

Effect of Operating Stresses on Elements of Shovel Swing Bearings; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

Electromagnetic Method for Resonance Tuning of a Mechatronic System; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Tomilin A. K. Aleksander Konstantinovich
Cyhoeddwyd: (2015)

Prospects of Creating Products Using Selective Laser Sintering; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

The Models of Supporting the Strategic Decisions on Engineering Products Competitiveness; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Tceplit A. P.
Cyhoeddwyd: (2015)

Process Water Treatment at Metallurgical and Machine Building Enterprises; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

Comparative Analysis of the Lip Seal in Hydraulic Power Cylinder; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Buyalich G. D. Gennadiy Daniilovich
Cyhoeddwyd: (2015)

Using of Information Systems for Socio-Economic Management Applications in Mechanical Engineering Enterprises; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Bleikher O. V. Oksana Vladimirovna
Cyhoeddwyd: (2015)

Application of Natural Barium-Stroncium Containing Material for Steel Treatment; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Platonov M. A. Maksim Aleksandrovich
Cyhoeddwyd: (2015)

Determination of Kinematic Parameters of Rotary Transmission Tooled with Hydraulic Cylinders; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

Numerical Optimization Method of Spacecraft Antenna Retargeting Point Calculations; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

Monitoring Positioning Accuracy of the Basic Functional Units of Technological Machines; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Mescheryakov Y. E.
Cyhoeddwyd: (2015)

Indirect Negative Influence of Coal Mine Motor Vehicles on the Environment; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Portola V. A. Vyacheslav Alekseevich
Cyhoeddwyd: (2015)

The Subjects of Automated Competitiveness Monitoring of Science-Intensive Products in Engineering; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Tashchiyan G. O. Grigory Olegovich
Cyhoeddwyd: (2015)

Parameters of Contact Interaction while Lathing with Straight-Edge and Radius Cutters; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Filippov A. V. Andrey Vladimirovich
Cyhoeddwyd: (2015)

Influence of Preliminary Deformation on Micromechanisms of Failure of Offshore Gas Pipeline Material; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

Electronic Circuit Design of Power Supplies for Welding in Ltspice Iv Program; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
gan: Krampit M. A. Maksim Andreevich
Cyhoeddwyd: (2015)

Providing of High Longevity of Operating Parts of Small-Scale Machinery in Agriculture; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

Modeling of the Potential Pit and Force Field to Limit the Motion of the Plasma Particles; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Cyhoeddwyd: (2015)

Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering: International conference, December 11-12, 2014, Yurga, Russia; [proceedings]; Applied Mechanics and Materials
Cyhoeddwyd: (2015)