Influence of Chip Formation Characteristics on Flank Contact Load Distribution in Titanium Alloy Cutting
| Parent link: | Applied Mechanics and Materials: Scientific Journal Vol. 756 : Mechanical Engineering, Automation and Control Systems (MEACS2014).— 2015.— [P. 126-131] |
|---|---|
| প্রধান লেখক: | |
| সংস্থা লেখক: | |
| অন্যান্য লেখক: | |
| সংক্ষিপ্ত: | Title screen In this paper different contact conditions between tool, chip and work material are analyzed. Experimental and theoretical studies of contact load distribution on the artificial flank wear land of the cutter in free orthogonal turning of a disk made from titanium alloy (Ti-6Al-2Mo-2Cr) are described. Investigations of cutting with various feed rate and cutting speed show that the greatest contact loads are observed immediately at the cutting edge. It is associated with the discontinuous character of titanium alloy chip and the elastic recovery of the transient (machined) surface at the moment when generated chip element is separated. The main influence of the variable chip thickness ratio of the discontinuous chip on the value of the greatest normal contact load near the cutting edge is shown that confirms the author’ hypothesis about a sag of the transient surface in the cutting edge region. Режим доступа: по договору с организацией-держателем ресурса |
| ভাষা: | ইংরেজি |
| প্রকাশিত: |
2015
|
| মালা: | Mechanical Engineering, Processing and Surface Engineereng, Metals Treatment, Equipment and Tools |
| বিষয়গুলি: | |
| অনলাইন ব্যবহার করুন: | http://dx.doi.org/10.4028/www.scientific.net/AMM.756.126 |
| বিন্যাস: | বৈদ্যুতিক গ্রন্থের অধ্যায় |
| KOHA link: | https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=641289 |
MARC
| LEADER | 00000nla2a2200000 4500 | ||
|---|---|---|---|
| 001 | 641289 | ||
| 005 | 20240223132443.0 | ||
| 035 | |a (RuTPU)RU\TPU\network\6189 | ||
| 035 | |a RU\TPU\network\6188 | ||
| 090 | |a 641289 | ||
| 100 | |a 20150515a2015 k y0engy50 ba | ||
| 101 | 0 | |a eng | |
| 105 | |a y z 100zy | ||
| 135 | |a drcn ---uucaa | ||
| 181 | 0 | |a i | |
| 182 | 0 | |a b | |
| 200 | 1 | |a Influence of Chip Formation Characteristics on Flank Contact Load Distribution in Titanium Alloy Cutting |f V. N. Kozlov, X. Li | |
| 203 | |a Text |c electronic | ||
| 225 | 1 | |a Mechanical Engineering, Processing and Surface Engineereng, Metals Treatment, Equipment and Tools | |
| 300 | |a Title screen | ||
| 330 | |a In this paper different contact conditions between tool, chip and work material are analyzed. Experimental and theoretical studies of contact load distribution on the artificial flank wear land of the cutter in free orthogonal turning of a disk made from titanium alloy (Ti-6Al-2Mo-2Cr) are described. Investigations of cutting with various feed rate and cutting speed show that the greatest contact loads are observed immediately at the cutting edge. It is associated with the discontinuous character of titanium alloy chip and the elastic recovery of the transient (machined) surface at the moment when generated chip element is separated. The main influence of the variable chip thickness ratio of the discontinuous chip on the value of the greatest normal contact load near the cutting edge is shown that confirms the author’ hypothesis about a sag of the transient surface in the cutting edge region. | ||
| 333 | |a Режим доступа: по договору с организацией-держателем ресурса | ||
| 461 | 0 | |0 (RuTPU)RU\TPU\network\5920 |t Applied Mechanics and Materials |o Scientific Journal | |
| 463 | 0 | |0 (RuTPU)RU\TPU\network\6028 |t Vol. 756 : Mechanical Engineering, Automation and Control Systems (MEACS2014) |o International Conference, 16‐18 October, 2014, Tomsk, Russia |o [proceedings] |f National Research Tomsk Polytechnic University (TPU) |v [P. 126-131] |d 2015 | |
| 610 | 1 | |a электронный ресурс | |
| 610 | 1 | |a труды учёных ТПУ | |
| 610 | 1 | |a нагрузки | |
| 610 | 1 | |a износ | |
| 610 | 1 | |a инструменты | |
| 610 | 1 | |a титановые сплавы | |
| 700 | 1 | |a Kozlov |b V. N. |c specialist in the field of mechanical engineering |c Associate Professor of Tomsk Polytechnic University, Candidate of technical sciences |f 1958- |g Victor Nikolayevich |3 (RuTPU)RU\TPU\pers\32610 |9 16523 | |
| 701 | 1 | |a Li |b X. | |
| 712 | 0 | 2 | |a Национальный исследовательский Томский политехнический университет (ТПУ) |b Институт кибернетики (ИК) |b Кафедра технологии автоматизированного машиностроительного производства (ТАМП) |3 (RuTPU)RU\TPU\col\18705 |
| 801 | 2 | |a RU |b 63413507 |c 20161229 |g RCR | |
| 856 | 4 | |u http://dx.doi.org/10.4028/www.scientific.net/AMM.756.126 | |
| 942 | |c CF | ||