Engineering support for improving quality of layer-by-layer laser sintering; The 7th International Forum on Strategic Technology (IFOST-2012), September 18-21, 2012, Tomsk
| Parent link: | The 7th International Forum on Strategic Technology (IFOST-2012), September 18-21, 2012, Tomsk.— 2012.— [4 p.] |
|---|---|
| Autor principal: | |
| Altres autors: | |
| Sumari: | Title screen Improvement problem has been considered for a laser sintered surface layer. Purposely built experimental setup was decribed together with a four-factor experiment design on laser sintering PMS-1 copper powder. A mathematical model describing the effect of laser sintering process parameters on the surface roughness has been proposed. Practical recommendation for improving the quality of the surface layer is given. Режим доступа: по договору с организацией-держателем ресурса |
| Idioma: | anglès |
| Publicat: |
2012
|
| Matèries: | |
| Accés en línia: | http://dx.doi.org/10.1109/IFOST.2012.6357719 |
| Format: | Electrònic Capítol de llibre |
| KOHA link: | https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=636294 |
Ítems similars
The effect of layer-by-layer laser sintering on the quality of copper powder sintered surface layer; 11th International Forum on Strategic Technology (IFOST 2016); Pt. 1
per: Saprykin A. A. Aleksandr Aleksandrovich
Publicat: (2016)
per: Saprykin A. A. Aleksandr Aleksandrovich
Publicat: (2016)
Influence of Layer-by-layer Laser Sintering Modes on the Thickness of Sintered Layer of Cobalt-chromium-molybdenum Powder; Advanced Materials Research; Vol. 1040 : High Technology: Research and Applications 2014 (HTRA 2014)
Publicat: (2014)
Publicat: (2014)
Improvement of surface layer formation technology for articles produced by layer-by-layer laser sintering; Applied Mechanics and Materials; Vol. 379 : Innovation materials and manufacturing technologies, economic aspects in enterprises
per: Saprykina N. A. Natalia Anatolyevna
Publicat: (2013)
per: Saprykina N. A. Natalia Anatolyevna
Publicat: (2013)
Formation of Surface Layer of Cobalt Chrome Molybdenum Powder Products with Differentiation of Laser Sintering Modes; Applied Mechanics and Materials; Vol. 682 : Innovation Technology and Economics in Engineering
per: Saprykina N. A. Natalia Anatolyevna
Publicat: (2014)
per: Saprykina N. A. Natalia Anatolyevna
Publicat: (2014)
Low temperature sintering of electroexplosive nanopowders; Bulletin of the Tomsk Polytechnic University; Vol. 309, № 4
Publicat: (2006)
Publicat: (2006)
High Toughness Laminated Composites Fabricated from Ti3Al(Si)C2 Filled Preceramic Paper and Nb Foils: Formation Mechanism and Influence of Laminate Architecture; Advanced Engineering Materials; Vol. 26, iss. 13
Publicat: (2024)
Publicat: (2024)
Preceramic paper-derived SiCf/Ti3Al(Si)C2 and SiCf/Ti3SiC2 MAX-phase based laminates fabricated using spark plasma sintering; Scripta Materialia; Vol. 194
Publicat: (2021)
Publicat: (2021)
Layer-by-Layer-Assembled Capsule Size Affects the Efficiency of Packaging and Delivery of Different Genetic Cargo; Particle and Particle Systems Characterization; Vol. 38, iss. 2
Publicat: (2021)
Publicat: (2021)
Use of copper phtalocyanine adsorption layer for substraction of spirits in gasochromatographic analysis; Bulletin of the Tomsk Polytechnic University; Vol. 309, № 4
per: Gavrilenko М. А.
Publicat: (2006)
per: Gavrilenko М. А.
Publicat: (2006)
The research of a pulse laser powder materials sintering process; Materials Science Forum; Vol. 575-578
per: Saprykin A. A.
Publicat: (2008)
per: Saprykin A. A.
Publicat: (2008)
Layer-by-Layer technique as a versatile tool for gene delivery applications; Expert Opinion on Drug Delivery; Vol. XX, iss. X
Publicat: (2021)
Publicat: (2021)
Physical Layer Security in N-Pair NOMA-PLNC Wireless Networks; IEEE Access; Vol. 10
Publicat: (2022)
Publicat: (2022)
Remote Non-Destructive Monitoring of Thermophysical Properties Using Flash Technique; The 7th International Forum on Strategic Technology (IFOST-2012), September 18-21, 2012, Tomsk
per: Troitsky O. Yu. Oleg Yurievich
Publicat: (2012)
per: Troitsky O. Yu. Oleg Yurievich
Publicat: (2012)
Технология электродугового послойного выращивания металлических изделий; Прогрессивные технологии и экономика в машиностроении
per: Курбонов А. М.
Publicat: (2022)
per: Курбонов А. М.
Publicat: (2022)
Interfacial Distribution of Chemical Elements in Fe–Cr–V–Mn–C Coatings Produced by Electron-Beam Cladding in Vacuum; Russian Physics Journal; Vol. 65, iss. 1
per: Galchenko N. K. Nina Konstantinovna
Publicat: (2023)
per: Galchenko N. K. Nina Konstantinovna
Publicat: (2023)
Effect of radiation exposure on the structure and diffusion in the near-surface layer of ultrafine-grained nickel; Russian Physics Journal; Vol. 64, iss. 5
Publicat: (2021)
Publicat: (2021)
High-Temperature Oxidation of Laminated Ta/Ti3Al(Si)C2 Composites in the Temperature Range 800–1300°C; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 19, iss. 5
Publicat: (2025)
Publicat: (2025)
Structure and Phase Evolution in a SiC Ceramic Surface Layer During Electron-Beam Treatment; Refractories and Industrial Ceramics; Vol. 59, iss. 3
Publicat: (2018)
Publicat: (2018)
Influence of the energy fluence and the aluminum layer thickness on the ignition delay time of explosive materials by a laser pulse; Energy Fluxes and Radiation Effects (EFRE-2016)
per: Khaneft A. V. Aleksandr Villivich
Publicat: (2016)
per: Khaneft A. V. Aleksandr Villivich
Publicat: (2016)
Gas-Vapor Mixture Temperature in the Near-Surface Layer of a Rapidly-Evaporating Water Droplet; Entropy; Vol. 21
per: Antonov D. V. Dmitry Vladimirovich
Publicat: (2019)
per: Antonov D. V. Dmitry Vladimirovich
Publicat: (2019)
Исследование факторов, влияющих на качество поверхности, полученной лазерным спеканием; Обработка металлов (технология, оборудование, инструменты); № 4
per: Сапрыкина Н. А. Наталья Анатольевна
Publicat: (2011)
per: Сапрыкина Н. А. Наталья Анатольевна
Publicat: (2011)
Microstructure and Deformation Behavior of Novel Metal–Ceramic Laminated Composites Ta/Ti3Al(Si)C2–TiC; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 18
Publicat: (2024)
Publicat: (2024)
Characteristics of nanopowders produced by wire electrical explosion oftinned copper conductor in argon; Materials Lettersэ; Vol. 62, № 17-18
Publicat: (2008)
Publicat: (2008)
The Special Features of the Phase Formation and Distribution in the Titanium Nickelide Surface Layers Treated by Electron Beams; Russian Physics Journal; Vol. 58, iss. 5
Publicat: (2015)
Publicat: (2015)
Laser Technology for Use in Recycyling Printed Circuit Boards; Chemical and Petroleum Engineering; Vol. 58, iss. 5-6
per: Kuznetsov G. V. Geny Vladimirovich
Publicat: (2022)
per: Kuznetsov G. V. Geny Vladimirovich
Publicat: (2022)
Characteristics of Nanopowders Produced by Electrical Explosionof Tin–Lead Alloy Conductors in Air; Inorganic Materials: Applied Research; Vol. 2, № 12
per: Ilyin A. P. Aleksandr Petrovich
Publicat: (2011)
per: Ilyin A. P. Aleksandr Petrovich
Publicat: (2011)
Surface alloying of Al films/Ti substrate based on high-current pulsed electron beams irradiation; Rare Metals; Vol. 33, iss. 2
Publicat: (2014)
Publicat: (2014)
Optical temperature measurements in superheated liquid droplets; Experimental Thermal and Fluid Science; Vol. 175
Publicat: (2026)
Publicat: (2026)
Optimization of limiting modes of streamer semiconductor laser; Bulletin of the Tomsk Polytechnic University; Vol. 310, № 1
per: Parashchyk V. V.
Publicat: (2007)
per: Parashchyk V. V.
Publicat: (2007)
Cross section of the cut layer in oblique single-edge boring by a radial cutter; Russian Engineering Research; Vol. 37, iss. 4
Publicat: (2017)
Publicat: (2017)
Properties of powders produced by electrical explosions of copper-nickel alloy wires; Materials Letters; Vol. 61, № 14-15
Publicat: (2007)
Publicat: (2007)
Formation of nano-sized structural-phase states in surface layers of a cermet alloy and the influence of the states on the tool life of cermet plates in metal cutting; Applied Mechanics and Materials; Vol. 770 : Urgent Problems of Up-to-Date Mechanical Engineering
Publicat: (2015)
Publicat: (2015)
Paleographic features of formation of petroliferous layers of Vasyugan suite of Western Siberia; Bulletin of the Tomsk Polytechnic University; Vol. 311, № 1
per: Belozerov V. B. Vladimir Borisovich
Publicat: (2007)
per: Belozerov V. B. Vladimir Borisovich
Publicat: (2007)
Additive Manufacturing of Metal Products via Filler Wire Arc Welding (Review); Materials Science Forum; Vol. 1064
Publicat: (2022)
Publicat: (2022)
Lithologic and electrometric characteristic of productive layers of the gurarinckiy-sobolinniy deposit low-chalky adjourments; Bulletin of the Tomsk Polytechnic University; Vol. 310, № 2
per: Perevertaylo Т. G.
Publicat: (2007)
per: Perevertaylo Т. G.
Publicat: (2007)
Применение селективного лазерного спекания для изготовления горношахтного оборудования; Горный информационно-аналитический бюллетень; № 53
per: Сапрыкина Н. А. Наталья Анатольевна
Publicat: (2012)
per: Сапрыкина Н. А. Наталья Анатольевна
Publicat: (2012)
Chemical modification of gold surface via UV-generated aryl radicals derived 3,5-bis(trifluoromethyl)phenyl)iodonium salt; Progress in Organic Coatings; Vol. 136
Publicat: (2019)
Publicat: (2019)
Use of moss biomonitors for turbulent transport coefficient estimation for industrial emissions; Atmospheric Pollution Research; Vol. 8, iss. 5
per: Ryzhakova (Rizhakova) N. K. Nadezhda Kirillovna
Publicat: (2017)
per: Ryzhakova (Rizhakova) N. K. Nadezhda Kirillovna
Publicat: (2017)
Numerical Simulation of Thermal Processes and the Effect of Heating of Near-Surface Layers of Titanium on the Diffusion Transfer of Dopants during High-Intensity Pulsed Ion Implantation; Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques; Vol. 17, iss. 6
per: Ivanova A. I. Anna Ivanovna
Publicat: (2023)
per: Ivanova A. I. Anna Ivanovna
Publicat: (2023)
Radiolabeling Strategies of Micron- and Submicron-Sized Core–Shell Carriers for In Vivo Studies; ACS Applied Materials and Interfaces; Vol. 12, iss. 28
Publicat: (2020)
Publicat: (2020)