Магниевый сплав для медицинских применений после обработки экструзией; Инновационные технологии в машиностроении

Магниевый сплав для медицинских применений после обработки экструзией; Инновационные технологии в машиностроении

Detalles Bibliográficos
Parent link:	Инновационные технологии в машиностроении.— 2022.— [С. 14-17]
Autor principal:	Лугинин Н. А.
Autor Corporativo:	Национальный исследовательский Томский политехнический университет Исследовательская школа физики высокоэнергетических процессов
Otros Autores:	Ерошенко А. Ю. (научный руководитель), Легостаева Е. В., Шаркеев Ю. П. Юрий Петрович
Sumario:	Заглавие с титульного экрана Представлены экспериментальные результаты влияния структурного состояния магниевого сплава системы Mg-Ca на физико-механические свойства. Показано, что экструзия повышает прочностные и пластические свойства данного сплава. Experimental results of the influence of the structural state of the Mg-Ca magnesium alloy on the physical and mechanical properties are presented. It is shown that extrusion increases the strength and plastic properties of this alloy.
Lenguaje:	ruso
Publicado:	2022
Colección:	Технологии получения и обработки материалов в машиностроении
Materias:	труды учёных ТПУ электронный ресурс магниевые сплавы медицинское применение обработка экструзия интенсивная пластическая деформация механические свойства структура intensive plastic deformation mechanical properties structure magnesium alloy
Acceso en línea:	http://earchive.tpu.ru/handle/11683/72736
Formato:	MixedMaterials Electrónico Capítulo de libro
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=634630

Ejemplares similares

Влияние равноканального углового прессования на структуру и свойства антифрикционного сплава Al-40Sn; Известия Томского политехнического университета [Известия ТПУ]; Т. 323, № 2 : Математика и механика. Физика
por: Скоренцев А. Л. Александр Леонидович
Publicado: (2013)

Effect of Severe Plastic Deformation by Extrusion on Microstructure and Physical and Mechanical Properties of Mg–Y–Nd and Mg–Ca Alloys; Technical Physics; Vol. 67, iss. 12
Publicado: (2022)

Structure and Deformation Behavior of Ultrafine-Grained Zr-2.5Nb Alloy; AIP Conference Proceedings; Vol. 1909 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2017 (AMHS’17)
Publicado: (2017)

Enhancement of the mechanical properties of AZ31 magnesium alloy via nanostructured hydroxyapatite thin films fabricated via radio-frequency magnetron sputtering; Journal of the Mechanical Behavior of Biomedical Materials; Vol. 46
Publicado: (2015)

Влияние деформационно-термической обработки (a+b)-сплавов титана ВТ6 и ВТ22 на их коррозионную стойкость; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 334, № 4
Publicado: (2023)

Regularities of Macroscopic Localization of Plastic Deformation in the Stretching of a Low-Carbon Steel; Russian Physics Journal; Vol. 57, iss. 3
Publicado: (2014)

Effect of Hydrogen on the Deformation Behavior and Localization of Plastic Deformation of the Ultrafine-Grained Zr–1Nb Alloy; Metals; Vol. 10, iss. 5
Publicado: (2020)

Hydrogen Effect on the Evolution of the Structural-Phase State and Superplastic Properties of Ultrafine-Grained Ti-Al-V-Mo Alloy; Physical Mesomechanics; Vol. 25, iss. 5
Publicado: (2022)

Influence of Zr-1 wt.% Nb alloy structure state on its deformation and thermal behavior under quasi-static tension; Materials Letters; Vol. 285
Publicado: (2021)

Evolution of microstructure and mechanical properties of Ti-Nb-Zr and Ti-Nb-Zr-Ta-Sn alloys in severe plastic deformation; Materials Letters; Vol. 382
Publicado: (2025)

The Effect of a Severe Plastic Deformation by Groove Pressing on the Grain Structure of the Al-Mg Alloy; Key Engineering Materials; Vol. 743 : High Technology: Research and Applications (HTRA 2016)
Publicado: (2017)

Scale-dependent subsurface deformation of metallic materials in sliding; Tribology International; Vol. 43, iss. 4
Publicado: (2010)

Influence of Severe Plastic Deformation by Extrusion on Microstructure, Deformation and Thermal Behavior under Tension of Magnesium Alloy Mg-2.9Y-1.3Nd; Metals; Vol. 13, iss. 5
Publicado: (2023)

The morphology of the deformation relief and the grain boundary role in the bicrystals of AISI 316 steel; Solid State Sciences; Vol. 99
por: Alferova (Alfyorova) E. A. Ekaterina Aleksandrovna
Publicado: (2020)

Self-organization processes during deformation of nickel single crystals; Materials Characterization; Vol. 159
por: Alferova (Alfyorova) E. A. Ekaterina Aleksandrovna
Publicado: (2020)

Influence of ultrafine-grained structure of Ti-42Nb-7Zr alloy on energy dissipation and storage under quasi-static tension; Materials Letters; Vol. 375
Publicado: (2024)

Severe Plastic Deformation of Mg–Zn–Zr–Ce Alloys: Advancing Corrosion Resistance and Mechanical Strength for Medical Applications; Metals; Vol. 13, iss. 11
Publicado: (2023)

Bone marrow derived mesenchymal stem cell response to the RF magnetron sputter deposited hydroxyapatite coating on AZ91 magnesium alloy; Materials Chemistry and Physics; Vol. 221
Publicado: (2018)

Surface Modification of Mg0.8Ca Alloy via Wollastonite Micro-Arc Coatings: Significant Improvement in Corrosion Resistance; Metals; Vol. 11, iss. 5
Publicado: (2021)

Исследование тонкой структуры элементов кабеля технических сверхпроводников на основе сплава Nb-Ti при многоступенчатом волочении; Известия Томского политехнического университета [Известия ТПУ]; Т. 323, № 2 : Математика и механика. Физика
Publicado: (2013)

Structure and Phase Composition of Ultrafine-Grained TiNb Alloy after High-Temperature Annealings; AIP Conference Proceedings; Vol. 1909 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2017 (AMHS’17)
Publicado: (2017)

Estimation of dust cohesion for analysis of reliability of the environmental protective systems from dust pollution; The Third International Forum on Strategic Technologies (IFOST 2008), 23-29 June 2008, Novosibirsk-Tomsk
Publicado: (2008)

Effect of the structural and phase state on the deformation behavior and mechanical properties of the ultrafine-grained titanium alloy (Ti-Al-V-Мо) at temperatures in the range of 293-973 K; Materials Science and Engineering: A; Vol. 800
Publicado: (2021)

Structure, phase composition and mechanical properties in bioinert zirconium-based alloy after severe plastic deformation; Письма о материалах; Т. 7, № 4 (28)
Publicado: (2017)

Microstructure Stability and Mechanical Properties of Ultrafine-Grained Zirconium Alloy under Prolonged Thermal Exposure; AIP Conference Proceedings; Vol. 1783 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2016
Publicado: (2016)

Calculation of Stress-Strain State and Contact Stresses in the Process of Chip Formation; Solid State Phenomena; Vol. 313
por: Proskokov A. V. Andrey Vladimirovich
Publicado: (2021)

Subsurface structural evolution and wear lip formation on copper single crystals under unlubricated sliding conditions; Wear; Vol. 410-411
Publicado: (2018)

Research on the processes of deformation and failure in coarse- and ultrafine-grain states of Zr1–Nb alloys by digital image correlation and infrared thermography; Materials Science and Engineering: A; Vol. 784
Publicado: (2020)

Surface properties modification of magnesium alloys by low energy high current pulsed electron beam; Surface and Coatings Technology; Vol. 420
Publicado: (2021)

Comparative Investigation of the Influence of Ultrafine-Grained State on Deformation and Temperature Behavior and Microstructure Formed during Quasi-Static Tension of Pure Titanium and Ti-45Nb Alloy by Means of Infrared Thermography; Materials; Vol. 15, iss. 23
Publicado: (2022)

On the Observation of Slow Wave Processes in Deforming Rock Sample; Journal of Mining World Express; Vol. 2, iss. 2
Publicado: (2013)

Influence of hydrogen on mechanical properties of [012]-crystals of austenitic steel Fe-18Cr-14Ni-2Mo; Bulletin of the Tomsk Polytechnic University; Vol. 310, № 1
Publicado: (2007)

Comparative study of the structure, properties, and corrosion behavior of Sr-containing biocoatings on Mg0.8Ca; Materials; Vol. 13 iss. 8
Publicado: (2020)

Исследование влияния поверхностной пластической деформации материала бурильных труб на их технологические свойства; Известия Томского политехнического университета [Известия ТПУ]. Инжиниринг георесурсов; Т. 336, № 3
por: Буглов Н. А. Николай Александрович
Publicado: (2025)

Contactless and nondestructive evaluation of residual stress distribution in modified and pure HDPE materials using a novel terahertz method and line-scan thermographic technique; Composites Part A: Applied Science and Manufacturing; Vol. 183
Publicado: (2024)

Changes in the Structural-Phase State and Dislocation Density of Ti49.8Ni50.2 Alloy Depending on the Isochronal Annealing Temperature after Severe Plastic Deformation by abc Pressing at 573 K; Physical Mesomechanics; Vol. 27, iss. 2
Publicado: (2024)

Microstructure characterization and corrosion behaviour of a nanohydroxyapatite coating deposited on AZ31 magnesium; Vacuum; Vol. 117
por: Surmeneva M. A. Maria Alexandrovna
Publicado: (2015)

Composite MAO-PLGA coatings with improved mechanical and corrosion properties on Mg-Zr-Zn-Ce alloy in UFG state; Letters on Materials; Vol. 15, iss. 2
Publicado: (2025)

Speckle Pattern of the Surface Layer of Titanium Alloy GRADE 2 and Steel 3723HR Samples under Deformation; Materials Science Forum; Vol. 938 : Materials and Technologies in Mechanical Engineering
Publicado: (2018)

Thermoelectric Method of Plastic Deformation Detection; Materials Science Forum; Vol. 938 : Materials and Technologies in Mechanical Engineering
Publicado: (2018)