Pulsed Electron-Beam Melting of Cu-Steel 316 System: Evolution of Chemical Composition and Properties; 7 International conference on modification of materials with particle beams and plasma flows

Pulsed Electron-Beam Melting of Cu-Steel 316 System: Evolution of Chemical Composition and Properties; 7 International conference on modification of materials with particle beams and plasma flows

Dades bibliogràfiques
Parent link:	7 International conference on modification of materials with particle beams and plasma flows.— 2004.— [P. 258-262]
Altres autors:	Rotshtein V. P., Markov A. B., Ivanov Yu. F. Yuriy Fedorovich, Karlik K. V., Uglov V. V. Vladimir Vasilievich, Kuleshov A. K., Novitskaya M. V., Dub S. N., Pauleau Y., Thièry F., Shulepov I. A. Ivan Anisimovich
Sumari:	Title from the title-page. The surface morphology, chemical composition, nanohardness, and tribological properties of a film (Сu)/substrate (stainless steel 316) system subjected to pulsed melting with a low energy (20-30 keV) high-current electron beam (2-3 μs, 2-10 J/cm2) have been investigated. The film was deposited by sputtering a Cu target in the Ag plasma of a microwave discharge. To prevent the local delamination of the film due to cratering, the substrates were repeatedly pre-irradiated with 8-10 J/cm2. Single pulsed melting of this system results in the formation of a diffusion layer of thickness 120-170 nm near the interface, irrespective of the energy density. In contrast, an increase in number of pulses increases the thickness of this layer. For single irradiation, the nanohardness and the average wear rate of the surface layer of thickness 0.5-1 μm, including the molten film and the diffusion layer, nonmonotonically vary with energy density, reaching, respectively, a maximum and a minimum in the range of 4.3-6.3 J/cm2. Режим доступа: из корпоративной сети ТПУ Text files
Idioma:	anglès
Publicat:	2004
Col·lecció:	Modification of material properties
Matèries:	физика медь нержавеющие стали электронно-лучевая плавка химический состав трибологические свойства нанотвердость импульсное плавление труды учёных ТПУ электронный ресурс
Accés en línia:	http://www.lib.tpu.ru/fulltext2/c/2004/C13/042.pdf
Format:	Electrònic Capítol de llibre
KOHA link:	https://koha.lib.tpu.ru/cgi-bin/koha/opac-detail.pl?biblionumber=232086

Ítems similars

Modification of Microstructure and Properties of Martensitic Stainless Steel by High-Intensity Implantation of Nitrogen Ions; Surface Modification of Materials by Ion Beams (SMMIB-2019)
Publicat: (2019)

Исследование структуры и свойств порошковой стали AISI 410; Перспективные материалы конструкционного и функционального назначения
Publicat: (2022)

Влияние ионно-плазменной поверхностной обработки на фазовый состав и нанотвердость упрочненного слоя аустенитной нержавеющей стали; Перспективы развития фундаментальных наук; Т. 1 : Физика
per: Загибалова Е. А.
Publicat: (2019)

Modeling the Temperature Fields of Copper Powder Melting in the Process of Selective Laser Melting; IOP Conference Series: Materials Science and Engineering; Vol. 142 : Innovative Technologies in Engineering
per: Saprykin A. A. Aleksandr Aleksandrovich
Publicat: (2016)

Investigation of the effects of an intense pulsed ion beam on the surface melting of IN718 superalloy prepared with selective laser melting; Metals; Vol. 10, iss. 9
Publicat: (2020)

The possibility of modification of silumin by an electron beam; Междисциплинарные проблемы аддитивных технологий
per: Rygina M. E.
Publicat: (2018)

Surface modification of ZrO2-3Y2O3 ceramics with continuous Ar+ ion beams; Surface and Coatings Technology; Vol. 388
Publicat: (2020)

Flow and heat transfer evolution of PCM due to natural convection melting in a square cavity with a local heater; International Journal of Mechanical Sciences; Vol. 134
per: Bondareva N. S. Nadezhda Sergeevna
Publicat: (2017)

Эффекты неравновесной кристаллизации ионных кристаллов, индуцированные импульсным магнитным полем; Письма в Журнал технической физики; Т. 28, вып. 13
Publicat: (2002)

Modification of Ferrite Ceramics Properties by Intensive Pulsed Beam of Low-Energy Electrons; 7 International conference on modification of materials with particle beams and plasma flows
Publicat: (2004)

Microstructure and properties of Ti-6.5Al-3.5Mo-1.5Zr-0.3Si parts produced by electron beam melting; Journal of Physics: Conference Series; Vol. 1115 : 6th International Congress "Energy Fluxes and Radiation Effects", EFRE2018. 14th International Conference on Modification of Materials with Particle Beams and Plasma Flows (14th CMM)
Publicat: (2018)

The Structure-Phase State and Corrosion Resistance Modification of Austenitic Steel in Various Conditions Ion Implantation; 7 International conference on modification of materials with particle beams and plasma flows
Publicat: (2004)

Program-Controlled High-Voltage Pulse Generator for Ion Beams Source; 7 International conference on modification of materials with particle beams and plasma flows
per: Dektyarev S. V. Sergey Valentinovich
Publicat: (2004)

Electron-beam modification of coating – aluminum substrate systems; IOP Conference Series: Materials Science and Engineering; Vol. 71: International Scientific Conference of Young Scientists: Advanced Materials in Construction and Engineering
Publicat: (2015)

Comparative study of shock-wave hardening and substructure evolution of 304L and Hadfield steels irradiated with a nanosecond relativistic high-current electron beam; Journal of Alloys and Compounds; Vol. 714
Publicat: (2017)

Polymer melt pheology and flow birefringence
per: Janeschitz-Kriegl H.
Publicat: (Berlin, Springer-Verlag, 1983)

Исследование алмазоподобных покрытий, полученных методом импульсного осаждения; Современные проблемы машиностроения
per: Юрьев Ю. Н. Юрий Николаевич
Publicat: (2020)

The morphology of the deformation relief and the grain boundary role in the bicrystals of AISI 316 steel; Solid State Sciences; Vol. 99
per: Alferova (Alfyorova) E. A. Ekaterina Aleksandrovna
Publicat: (2020)

Mechanical Properties of Titanium Films Deposited by Pulsed High-Power Ion Beams; 7 International conference on modification of materials with particle beams and plasma flows
Publicat: (2004)

Основы техники кристаллизации расплавов
per: Гельперин Н. И. Нисон Ильич
Publicat: (Москва, Химия, 1975)

Influence of a high-power pulsed ion beam on the mechanical properties of corundum ceramics; IOP Conference Series: Materials Science and Engineering; Vol. 289 : Modern Technologies for Non-Destructive Testing
per: Kostenko V. Valeriya
Publicat: (2018)

Fabrication of multiple-layered gradient cellular metal scaffold via electron beam melting for segmental bone reconstruction; Materials and Design; Vol. 133
Publicat: (2017)

High Chromium Steel Modification by the Intense Discrete Electron Beam: Structure and Properties; Key Engineering Materials; Vol. 781 : Radiation-Thermal Effects and Processes in Inorganic Materials
Publicat: (2018)

Thermal-Kinetical Model of Laser Shrinkage of Ti-Nb-Alloy; AIP Conference Proceedings; Vol. 1783 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2016
per: Knyazeva A. G. Anna Georgievna
Publicat: (2016)

Low energy implantation of nitrogen ions by extended beam with a ballistic focusing in a stainless steel; Gas Discharge Plasmas and Their Applications (GDP 2019)
Publicat: (2019)

New Ti–35Nb–7Zr–5Ta Alloy Manufacturing by Electron Beam Melting for Medical Application Followed by High Current Pulsed Electron Beam Treatment; Metals; Vol. 11, iss. 7
Publicat: (2021)

Modification of the sample's surface of hypereutectic silumin by pulsed electron beam; IOP Conference Series: Materials Science and Engineering; Vol. 124 : Mechanical Engineering, Automation and Control Systems (MEACS2015)
Publicat: (2016)

The effect of Si content on structure and mechanical features of silicon-containing calcium phosphorus-based films deposited by rf-magnetron sputtering on titanium substrate treated by pulsed electron beam; The 9th International Forum on Strategic Techology (IFOST-2014), September 21-23, 2014, Cox's Bazar, Bangladesh
Publicat: (2014)

Combined effect of pulse electron beam treatment and thin hydroxyapatite film on mechanical features of biodegradable AZ31 magnesium alloy; IOP Conference Series: Materials Science and Engineering; Vol. 98 : Interdisciplinary Problems of Nanotechnology, Biomedicine and Nanotoxicology (Nanobiotech 2015)
Publicat: (2015)

On Erosion Mechanisms of the Solid Surface under the Treatment with Submicrosecond Ion Beams; 7 International conference on modification of materials with particle beams and plasma flows
per: Bleykher (Bleicher) G. A. Galina Alekseevna
Publicat: (2004)

Surface modification of selective laser melted Ti-6Al-4V parts by ultrasonic impact treatment and electron beam irradiation; Иерархические материалы: разработка и приложения для новых технологий и надежных конструкций
per: Sinyakova E. A.
Publicat: (2019)

Analysis of Dilatometry Data of the Stainless Steel 316L Bimodal Powder Sintering Process; AIP Conference Proceedings; Vol. 2051 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2018 (AMHS’18)
Publicat: (2018)

Создание упрочняющих покрытий электронно6лучевой наплавкой и последующей импульсной обработкой электронным пучком; Упрочняющие технологии и покрытия; № 1
Publicat: (2011)

Исследование зависимости нанотвердости деформационных структур монокристалов алюминия от числа циклов растяжения и величины нагрузки; Известия вузов. Физика; Т. 54, № 11 (3)
per: Кузнецов П. В. Павел Викторович
Publicat: (2011)

Low energy implantation of nitrogen ions by extended beam with a ballistic focusing in a stainless steel; Journal of Physics: Conference Series; Vol. 1393 : Gas Discharge Plasmas and Their Applications (GDP 2019)
Publicat: (2019)

Modification of Electric Properties of Lithium Niobate Crystals by Ion Bombardment; 7 International conference on modification of materials with particle beams and plasma flows
Publicat: (2004)

Mass Transfer of an Implanted Dopant in Materials under High-Power Pulsed Ion Beam Impact; 7 International conference on modification of materials with particle beams and plasma flows
Publicat: (2004)

Research of Protective Properties of Microplasma Coatings; 7 International conference on modification of materials with particle beams and plasma flows
per: Butyagin P. I.
Publicat: (2004)

Phenomenological Model of Dc Magnetron Discharge; 7 International conference on modification of materials with particle beams and plasma flows
Publicat: (2004)

On the Plastic Flow Localization of Martensitic Stainless Steel Saturated with Hydrogen; AIP Conference Proceedings; Vol. 1783 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2016
Publicat: (2016)